Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello,
I have currently cloned and built the latest master branch of Eclipse MQTT-SN Gateway https://github.com/eclipse/paho.mqtt-sn.embedded-c.git on my Nordic Border...
Dear N ordic S upport Team,
After I updated the nRF Connect SDK (1.4.0 to 1.5.1) and the Modem firmware (1.2.2 to 1.2.3) on my nrf9160 DK devices, the date time isn't synchronized...
Hello there,
It is actually basic for the Bluetooth connection for the nrf52840 using Zephyr, which changed the scan filter by name based on the central UART sample.
As...
Hi there,
We are currently using IAR embedded workbecnh IDE for our development on non-Nordic products. We are thus considering the possibility of also porting our Nordic...
Hi Nordic Support,
I am getting zero distance value from sensor(vl53l0x). I used SLAVE_ADDRESS =0x29 and register address=0x01. My code is mentioned below
void data_handler...
We originally saw (and reported) this problem with nRF5 SDK 4.1.0. We switched to nRF Connect SDK 1.6.0 which did not exhibit this problem. Now we just tested with nRF Connect...
Hi, I'm trying to found a way to flash production config for a project based on zigbee NCS example with OTA. Is nrfutil still a valuable tool for creating a production config...
Hi.
I'm trying to emulate my project, which is intended to run in either nRF9160 or nRF5340 boards (both using Arm Cortex-M33 processor), using QEMU, but as far as I know...
Hello,
I am using nRF52840 microcontroller to communicate with an external integrated circuit, through I2C peripheral . The project is using the latest Nordic SDK: more...
Hello,
I am running 1\nRF5_SDK_17.1.0_ddde560\examples\dfu\secure_bootloader\pca10040_s132_ble\ses example of SDK 17.1.0. Now, I want to update the firmware when it is pressed...
Dear Ladies and Gentlemen,
I read for detecting angle of arrival the following page:
https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples/bluetooth...
Hi,
I want to develop simple app that receives data via BLE and send it through UART so I could gather them to file or draw a real-time chart in SerialPlot.
As far as...
Running the secure DFU example in SDK 17.1.0 results in hardfault in IAR EWARM 9.10.2. The board used is PCA10040.
Using EWARM 8.50.4 seems to work without problems.
Steps...
I have a number of custom projects and boards that were created using SES.
How do I get nRF Connect to see my projects and boars. I have a separate directly structure where...
