Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Hello all,
I just found out that the nRF Connect extension for VSCode has been release, which is great news. Good job Nordic Team! I have followed the steps described in...
Hi, dear Nordic.
I'm using BC805M Module which uses nRF52805 SoC. What's the max sink/source current for individual pin OR total chip, please? Where could I find relative...
Hi,
Im using nrf9160 based custom board, nrf sdk 1.5.1.
I want to get the time from NTP servers, for that i connected to CATM1 n/w, connected to NTP server using UDP Protocol...
Hello, I am working with custom board nrf52840 and SDK 17. I am doing some changes to the project and I am getting an error that the SDK is using VFP register arguments but...
Hi,
I am getting this error message when using the nRF52 dev board but not when using the nRF51 dongle. I receive few packets and then it disconnects with this error message...
For example, I'd like to add library at_cmd_parser to my project. (It's under /ncs/nrf/lib/at_cmd_parser.)
My project is out-of-tree in its own directory. I tried in CMakeLists...
Does unblocked saadc sample the buffer size and stop or does it start re-sampling after the callback? In other words, if the buffer is 100 entries in length, will it issue...
I was able to write some I2C code to successfully work with the TCS34725 by porting a library from Arduino without fully understanding what was going on. Now I have to port...
Hello,
I am using th PCA10040 board, and I can build my project without problems. But when I debug it, 'stopped by vector catch' error appears. I have been reading possible...
hello Nordic
i am working with nrf52840, with zephyr (i am new to zephyr)
i have an issue with not responding pin interrupt so i try to run zephyr example to see how...
nRF9160 DK NCS v1.6.0, SLM with:
CONFIG_SLM_GPIO_WAKEUP =y
CONFIG_SLM_INTERFACE_PIN =24
Sometimes after at#xsleep=0 and several pulses on pin 24 SLM wakeups with...
Hi. I'm testing the multi-image DFU in nRF Connect SDK 1.7.0. I'm seeing an issue with the firmware images not getting reverted when it should.
Here's what I'm doing:
...
Hello!
I am having unexpected issues in setting TX power using Softdevice call to SD_BLE_GAP_TX_POWER_SET via sd_ble_gap_tx_power_set. Please see the code below.
The...
I am developing with 52840.
We checked button-related problems while using the source that checked the behavior on the DK board on the adafruit-circuit-playground-bluefruit...
