Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hi,
We are porting our application from nRF Zigbee & Thread SDK to NCS.
On the ZIgbee side, we have been using this methods:
1. zb_zdo_find_bind_src(): to check...
I'm working on a project that has multiple custom partition manager configuration file that are implemented based on the instructions provided in this section of the partition...
Hi,
yesterday, I met the same situation as here . But now, I can't even see one log, even after I annotated the code related twi and just remained some “NRF_LOG_INFO（）”...
Hi,
I am using SDK 17.0.2 for a simple scanner project, where nordic SoC is communicating with main MCU via SPI. The code starts normally on nRF52832, but on nRF52833, it...
Hi,
I am running the example ble_app_att_mtu_throughput with the nRF5 SDK on two nRF52840-DK dev kits. I have flashed both dev kits with S140 soft devices prior to flashing...
We are finalizing a product that has a BL652 (nRF52832) in the main unit and a BL651 (nRF52810) in a remote control unit. We are trying to get our regulatory radio testing...
When I changed HFCLK from "64 MHz internal oscillator (HFINT)" to "64 MHz crystal oscillator (HFXO)", the power consumption when executing sd_app_evt_wait() became larger...
Hi,
We've created a FW image targeting a PCA10056 which consists of our application FW, the example secure DFU bootloader over USB, and the softdevice. Everything works...
I have the ws2812 example working with ncs v1.5 on board actinius_icarus_som
However, when I combine it with other code such as for a custom SPI device and udp comms it...
Hello,
I contact to you because a customer is interested on the RF System, part number nRF5340-QKAA-R, and they asked the following below;
"
Customer wondering if you...
I added FOTA_DOWNLOAD and MCU_BOOT to my project.Then I want to use http to download a file, and an EBADMSG error occurs at this time.
I reproduced this problem in the download_test...
We have an I2S implementation that I based on the example code, but using the nrfx driver. Audio plays fine, but after I call nrfx_i2s_stop, I first see that no next buffers...
I didn't change anything and compile the source file from github. But my thingy52 keeps flashing and stays in DFU mode after new app hexfile was burned in
https://github...
Hi.
I use ble_app_hrs example.
Environment is follows.
- PCA100040 , nRF52 DK
- nRF SDK v17.0.2
- Galaxy Note10 mobile Phone
Bonding process is always fail...
