Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hello!
So I can connect, disconnect and write to my applications characteristics via a PyQt5 GUI I threw together. On the python backend, I use Bleak to
search for devices...
Dear Nordic Support,
Processor: nRF52840 / S140 soft device / SDK 15.3.0
I have a question about the use of the HFCLK in relation to the soft device. Our board has both...
Take a look at a following code
void fmc_serial_rx_cb(const uint8_t* p_data, uint32_t length)
{ __LOG(LOG_SRC_APP, LOG_LEVEL_INFO,"\n-------------SERIAL RECIEVED : %s...
I am new to softdevices so please bear with me for long list of questions.
I am evaluating SDK15.2.0 examples one-by-one. I came across eddystone example (ble_app_eddystone...
Hi!
In older SDK (15.0) has been present NRF_ESB_BUGFIX_TIMER and it initialization. Now (SDK 15.2/15.3) defines this macro but not use it. Is it bug or obsolete code?
Hello Nordic Team,
I followed the tutorial as you say( https://devzone.nordicsemi.com/tutorials/b/getting-started/posts/nrf52840-dongle-programming-tutorial ). But when...
dear all,
I'm a newbie on blue tooth low energy development, I have some really basic questions that I hope someone could answer, thank you very much in advance!
what...
Hello,
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. Switch sequence followed when LED 3 and 4 starts blinking, but get the devices list...
Hi I have central device which has array of MAC address to connect.
when i see the structure of sd_ble_gap_connect() i cannot pass a uint8_t addr[5] as input.
so i tried...
SDK v11.0 & NRF51822 QFAC
I encountered a problem. In the process of pstorage processing flash data, a serial port interrupt came in, resulting in a system reset.
I used...
Hi,
I have discovered a (rare) problem where the S132 stack get stuck in connected state when it is not actually connected anymore.
This behavior was first reported by...
Hi,
SDK - nRF5_SDK_15.2.0_9412b96
HW - nRF52840 connectivity chip, other controller for application chip
We are tried to port serialization application on other than...
HW - nRF52840
SDK - nRF5_SDK_15.2.0_9412b96
We are running connectivity example in nRF52840 and connected UART with serialization application over UART which is different...
First proof-of-concept super-simple nRF51 board. When we load software onto this board, will we have to tailor or configure the software to bypass or disable any functionality...
Our application is similar to a wireless keyboard. The events are very sparse but we need low latency (~50ms). If I understood correctly, BLE is a synchronous protocol, meaning...
