Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Hello,
I am facing an issue with SPI when the SoftDevice S132 is enabled and i cannot figure out what the problem is.
The following test works perfectly when SoftDevice...
Hi,
We have developed SLM(serial LTE Modem) application based on nRF Connect SDK 1.2.0 for nRF9160 chip. Now we want to port previous SLM application to nRF9151 chip based...
Hi Team,
I am facing an issue while converting the nRF Connect SDK v2.3.0 (downloaded from Visual Studio Code with nRF Connect) to a .emProject file for Segger Embedded...
hellow
I built my own Bluetooth receiver to connect different products from my company. The data transfer services of the two products are different. I want to use one host...
Hello, while writing a simple uart application, I noticed something peculiar in my code. I add led toggaling so I'd know if the code runs or not. I forgot that I disabled...
When upgrading the firmware of 54H20 using suit, compilation errors occur when calling the flash operation functions (flash_area_open, flash_area_erase, flash_area_write....
Hello. I get an error when trying to add a build configuration for a project based on a blink for a custom board on the nrf 52832 qfaa chip. Please tell me how to fix the...
Hello Nordic Team,
I am using my custom board, which uses nrf52840 qfaa chip. I am working with nRF Connect SDK v2.8.0
When I worked with blinky project on nrf52840DK...
Hi,
piggying-back on BT nus shell sample (workspace project), I try to define my own dt nodes.
I keep getting error like devicetree error: /aliases: undefined node...
Hi ALL,
v2.8.0,NRF54L15DK,I would like to ask：
1. if my pin is P0.00, is nrf_gpio_pin_set(0) correct？
2. If my pin is P1.01, is nrf_gpio_pin_set( 33 ) correct？
Hi,
I would like to flash the ad sample on Nrf54L15-PDK
Flash ends with error messages:
build messages:
I'm I tried running west flash --recover.But it didn...
I have completed a mouse program with 52840, but there are some problems at the moment. On some computers, usb will fail to obtain the descriptor, but there is no problem...
One last issue to crack. This one has been in production for a while and hasn't caused any issues other than a little annoyance to the customer. By my measurement when RTC...
Hello,
In regards to the nRF Connect SDK...
I am looking into the possibility of switching out the current implementation of AES used by the Bluetooth firmware. I am curious...
the pin for XL0 and XL1 is P00 and P01
but in my project, I need P00 and P01 works as UART.
I set the parameter to start inner RC clock.and find that: LFCLKSTAT show the...
my costom board is based upon the BT840F fanstell board. I know that this board is based on the nrf52840 QIAA SOC. but I also understand that nrf52840 QIAA has different configurations...
