Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
nRF5340Dk with NCS 2.6.1 and toolchain 2.6.1.
I want to measure 6 frequencies for my application, these frequencies would be attached to GPIO pins and needs to be measured...
Hi, I'm learning the nrf51-powerdown-example <system_off_wakeup_on_gpiote> from github.
My understanding of the code is:
1) When button 0 (Power down) button is pressed...
Hello, trying this and that with a qwiic relay , first a test on i2ccl then VS using a 9160DK. (i2ccl -> pip install i2cdriver ) returns a status of 0x00 that relay is not...
NCS 2.7 with sysbuild + mcuboot
NRF52840 (custom boards)
In my previous projects with NRF5 SDK I found it was very helpful to define a section in the linker so the rtt...
Hi,
I have a two part question aimed at optimizing the battery life during BLE transmissions. I am using an nRF52805 with the S112 soft device and a DCDC regulator connected...
Hi,
We have a custom board with a nRF9151. We're still sorting out LTE connectivity issues but I wanted to try out the location services with GNSS only for now. I modified...
I am building a Bluetooth controller with channel sounding feature enabled. The project uses an external Bluetooth host along with the hci_uart example. The prj.conf file...
Hello, I am using nRF Connect SDK version 2.9.0, and I want to know how to perform the software interrupt.
Where can I find the driver of the software interrupt to know...
startup_config.h is included in the file 'arm_startup_nrf51.s' but it does not exist in the nrf5 SDK. Where is it located?
I note there is a comment about the nrf5...
I have the same application that runs on both nrf51 and nrf52 MCUs. The Bluetooth in the application uses SoftDevice and not the SDK primarily because I started with the pc...
While evaluating low power mode on SBC I notice something strange:
- PPK II measuring 76mA
- LAB power supply measuring 67mA of supply current
- Digital multi meter...
I have nRF Connect SDK v2.9.0 and an nRF54L15 DK.
Is it possible to build the Zigbee NCP Sample for this board?
The source files under the Zigbee NCP Sample directory...
Hello everyone,
I have zepyhr running on the Cyclone V according to the following instructions: https://docs.nordicsemi.com/bundle/ncs-2.5.2/page/zephyr/boards/arm/cyclonev_socdk...
Hi,
I am using the SAADC (AIN2) to get temperature values from a Pt1000, and I am experiencing sometimes strange behaviour after the offset calibration is done.I have quite...
I am working with the NRF5340 to develop a BLE audio streaming application using a PDM MEMs microphone.
I have played around with the NRF5340 Audio DK and got PDM audio...
