I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
Hi, I want to update the modem firmware devices(in the field).I am using nRfconnect sdk 1.5.0 and hardware is brf9160 SICA B1 . current modem firmware is 1.2.3 . I tried to...
I tried to define an event as in attached figure. During Build, the error in the as shown in the attached imageoccurs. Where to define Log Configurations ? I ading custom...
cpu info:nrf5340
software:nrf connect sdk 1.6.1
hi professor,
In the uart interrupt I call k_fifo_put to trigger rx process thread but it is not take effect.What person...
Hi,
we are developing a system based on device with nRF52840 S140 ( central and pheripheral).
We developed on both side a custom service.
System is working fine bonding...
I'm new to the Bluetooth mesh world and I'm trying to change some basic configuration parameters during runtime, by modifying the Light Switch example. I've searched around...
Hello,
We are using Zephyr v2.6 and nRF51822 SoC in our project.
Because we are porting the code from the SDK environment into the Zephyr environment, we decided to use...
Hello everyone,
in the last chapter of
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/getting-started/posts/nrf-connect-sdk-tutorial---part-1-ncs-v1-4...
Hi,
I have removed UART from my custom board dts file as in my current application, I am not using UART for any transfer.
But due to this, I am unable to compile code...
Dear Forum,
I already succeeded in using the Nordic Toolbox's DFU-App to update the firmware of a BM833 via secure bootloader. I found out, that the Android DFU App is available...
Greetings,
Which Bluetooth LE examples in NCS v1.9.1 are suitable for the nRF52810?
I tried the usual suspects. peripheral_uart overflows flash and RAM.
peripheral_lbs...
The documents for setting up and using a Matter network require a change to account for new behavior of the chip tools.
https://developer.nordicsemi.com/nRF_Connect_SDK...
Hi Support Team,
we use the nrf52840-dk board to capture a bunch the emitted power of WiFi sources. In other words, we simply capture RSSI values until the data if full...
According to the official BLE core specification, in the scanning state:
"If the scanWindow and the scanInterval parameters are set to the same value by the Host, the Link...
I am using twi_scanner example program from nrf_sdk. when I run this program I could able to get the i2c address of some devices i.e., mpu6050 with address 0x68 and I am not...
