I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
I'm trying to drive the RGB LED light on the Thingy:91. So far, I've not been successful. I was hoping that by listing the steps I perform I might be able to get some advice...
Hi,rotocol
In Nordic's Smart Remote 3, it is mentioned that IR transmitter is protocol agnostics while IR driver is Protocol specific. Is it possible to write a common IR...
Hi,
Is there any battery life calculations for NRF52 and NRF51 (Beacon)?
For example: if TX power of NRF52 is 0 dBm and it broadcast every 5 seconds ? Or with any other...
Hello
I am working with nRF5340 and made the project according to "the first step to build". I want to add some libraries to my project but I can not. The libraries I want...
Hello, I am using MX25R1635FZUIL0 with nrf52 and my device is working with freertos. I have three different tasks using/accessing the flash functions but when i read back...
I use nRF52840 to creat a project. IDE select SEGGER. before everything is normal. when I update the SEGGER TO 5.42 version. i build the same project. there is one error.Please...
Hello, according to the latest nrf5 SDK documentation, the nrfx_gpiote_init function takes no argument, but if I call nrfx_gpiote_init() in a zephyr application, I get the...
To reproduce this problemm Ive added a device to the I2C that does not respond to a read command. The `i2c_read` call first returns `-EOI` (-5) and for every other i2c funcion...
The device nRF52832 cannot connect over SWD and generates the following error.
- Connecting via USB to J-Link device 0 - J-Link firmware: J-Link EDU Mini V1 compiled Apr...
After configuring the options for an nRF project, segger studio cannot create the project by warning me the error: "create_nordic_project.py failed"
The problem seems to...
I'm trying to make MQTT publisher example work using a BMD-340 evaluation board and nRF5 SDK for Thread and Zigbee 4.1.0 . I'm using a Raspberry Pi 3B with a Raspberry Pi...
Hi,
We have been using the MQTT sample code with a few iBasis SIM cards for some time without issue. This week we made a test where the mqtt_disconnect function in the sample...
I got the BLE mesh SDK from: http://www.nordicsemi.com/eng/Products/Bluetooth-low-energy/nRF5-SDK-for-Mesh/(language)/eng-GB
I want to develop a mesh gateway to connect...
Dear friends,
We plan to develop a mesh gateway, however, i found the SDK only offered a mesh serial example which based on python, but our platform can't support python...
