I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
refer to: http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_multi_image.html developer.nordicsemi.com/.../partition_manager.html
Where I change those image...
My accelerometer readings appear in my segger embedded studio "Debug Terminal" window.
It looks like this.
I want to stream the data via COM port to this "serial oscilloscope...
~/ncs/nrf/include/dfu/dfu_target_mcuboot.h int dfu_target_mcuboot_done(bool successful);
/////////////////////////////lack of this in last #ifdef __cplusplus } #endif
I am using mesh SDK v4.2.0.
I read the documentation of the remote provisioning example (pb_remote) and took look at the code.
My first feeling was that the remote provisioning...
To the kind attention of Nordic support team,
I'm working on a nRF52 based product, I saw using your sniffer that after LL_CONNECTION_UPDATE_REQ
I have got a Window Offset...
We have an nRF52 DK and have developed a customer board. On the custom board we have a header with pins for power, ground, clock, and data.
When I connect this to the nRF52...
Hi,
I've got ANCS working well in my application, but I seem unable to increase the length of the notification's message that I receive.
BLE_ANCS_ATTR_DATA_MAX is defined...
Dear sir,
I have an two problem:
1) Once change the device mane, after system rest some junk value is stored Note : here the device name read from the flash memory ...
I'm trying to run Provisioner Example on my nrf52840 DK, which is in examples/provisioner directory, . First I've build softdevice on DK and then I'm trying to build provisioner...
Hey NordicSemi. In my new project, I use DK NRF9160 and I need to determine the location. Since hardware GPS does not work, I decided to use the detection of coordinates through...
Hi,
Something locks-up my I2C sometimes and I need to make I2C recovery. It looks like Nordic has not implemented the zephyr i2c_recover_bus function, so I guess I need...
I'm looking for dual core inter task communication examples
where a thread on one core is interacting with a thread on the other core ?
e.g. will there be some kind of...
Hello All,
I was looking at the Digi XBee3 modules for a ZigBee project I am working on. What is great is they allow you to write MicroPython code to control the network...
I am trying to send some values from nRF52810 Board to my Laptop. I am using a nRF52840 Bluetooth Dongle to connect the board to my laptop. I am using the "Heart Rate Collector...
