I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi everyone：
New to the DevZone, nice to meet you guys.
I have an problem to the GPIOTE.
I'm now using an AFE4404 to calculate the heart rate and heart rate variability...
Hello, teams!
I'm sorry to bother you.
Now I'm testing mesh function.
I have two questions.
1) Is there good way to show the performance of relay operation?
...
Based on nRF52840 datasheet, to configure the QSPI peripheral, it is necessary to activate the external flash memory interface using ACTIVATE task. Our problem here is, during...
Hi,
I am using nRF52832 in a custom board for sending data. I need a reference voltage for my instrumentation amplifier around VDD/2, my VDD is about 2.7 V, so 1.3 V will...
Hi team,
Want to consult you on PA usage, my customer wants to achieve +16dBm PA, so if he has our 840 in +8dBm TX power, only needs +8dB for the PA or we would recommend...
Hi,
I would like to connect two centrals to one peripheral with >= BLE 4.3. I know,
normally one central is connected to multiple peripheral, but in this case,
a special...
I got an error when trying to build the dimming_client_nrf52840 example.
Simple error:
build/dimming_client_nrf52840_xxAA_s140_7.0.1_Debug/obj/ses_startup_nrf_common.o...
SDK 16, S132 V7.0.1, NRF52832, custom device, custom firmware.
Hello,
I want to keep beaconing advertisement (not connectable advertisement) while the BLE is connected...
Hi,
I have a question concerning the SIG qualification. We use the ublox BMD-350 (nrf52832) that is qualified as a component (QDID 101018). I don't really understand the...
Hello,
We are using nRF52840 chip with S140 with ble_app_blinky example.
I was merging Serial DFU bootloader, SoftDevice, application and BLE settings with below commands...
Hi,
I am trying to implement DALI-104 (IEC-62386:104:2019) on top of Thread protocol.
I am using Thread: CoAP Client and Thread: CoAP Server and want to configure these...
Hi,
I wrote my codes to toggle notification on and off using a button using nRF25840-DK and sdk v15. The task looked a simple one; however, I hit some issues such as error...
Hello Nordic Team,
We are working on a project based on nrf51822, we have a problem regarding the incorrect ADC values while waking up the microcontroller from System...
Hello,
I'm developing a custom asset tracker board. My software is currently a very lightly modifed asset tracker v1; my provider currently only support NB-IoT, firmware...
