before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I'm trying to do a low power sleep of 1s directly after a device reset, i.e. in Reset_Handler().
During this stage, my application does not allow any interrupts.
So my...
Hello DevZone community!
I'm having trouble debugging more than one board at the same time in a Linux development environment.
For a single board, I can debug either...
hello, i am using nrf52 dk .I was testing example twi scanner.I want to read slave address.So i am using twi scanner example but i got error message as follow:
TWI:INFO...
Hi, I'm new here and I use nRF52832 (pca10040), I was wondering if it is possible to change a function in C / C ++ language during the runtime, that is, my idea is whenever...
Hi,
I had a problem using your (nRf's) implementation of block device with my flash memory (I think that exact model is not relevant here). I'm using SDK 15.2 with NRF52840...
Hi,
Do you have a declaration of conformity for the chipset nRF52832 ?
I need this document to justify to my laboratory the conformity of the Bluetooth module to the standard...
hi,
I have some questions, please help me solve these questions. ( I use SDK 15.2.0 and nRF52832)
1. my customer ask how many central bonded with one nrf52? (my project...
Hello,
I am trying to send data from my light switch mesh client (nRF52840) to my gateway, the nRF9160 using UART. I added the UART functionality to the light switch client...
Hello there,
I followed all the steps in the following link:
http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.nrf52%2Fdita%2Fnrf52%2Fdevelopment...
My device (nrf52832) has two signals triggering GPIOTE interrupts. I need to be as low power as possible, so both are setup to not use hi accuracy, making them share the PORT...
i need a help
As mentioned in this thread
https://devzone.nordicsemi.com/f/nordic-q-a/18512/directed-advertising-with-pre-shared-irk
in need to do directed advertising...
Hi,
We want to measure our external custom board which is not based on nRF52 chip. That board has current consumption header and it's chip draws maximum current of 60mA...
Hi:
I find a odd question when i use SES to develop nRF52832, ESB protocol is using and i need to config some different slaves with same code except the pipe num, i define...
Hello,
In my current zigbee project I have a sensor end device which should sleep when possible. I am handling the ZB_COMMON_SIGNAL_CAN_SLEEP event and have added zb_set_rx_on_when_idle...
Hi,
I am using NRF52 SDK version 15.3, Segger Embedded Studio.
I am using the ble_app_beacon example in examples/ble_peripheral, I have programmed 2 devices with the...
