Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I'm using the UART / Serial Port Emulation over BLE example on the nRF52 development kit connected to a custom microcontroller.
I just need the nRF52 to simply relay bytes...
Hi everyone,
I have been looking for information about this, but I have not been able to find anything. I would like to send data employing UART, but I can not use the...
Hi, I have a few general questions on nus_data_send().
First off, is there another known way of transferring an array/string via ble to the Nordic mobile app other than...
Dear Sir,
I am working with nrf52832, SDK15 and s132 soft device.
I am using RIGADO DK .
Is it possible to continue advertising(from peripheral device) even after...
Hi All
I am doing a project which is base on SDK15.2 examples\proprietary_rf\gzll\gzp_dynamic_pairing\host\pca10040\blank\arm5_no_packs
I would like to add a timer to...
Hello,
I cannot add SPI0 to my application because OpenThread library was built with it without any interest of that. Could you fix it please ? (I need the 3 SPI peripherals...
Hello! I want to use the start time of the XOSC16M in NRF24LE1. I got ~4 ms. Can I put the processor to sleep at this time in standby mode? How to do it to wait for wakeup...
Hi all:
I see the "ant_share_channel _master_to_master" example,
this example is share_master,
my question is,
How to get p_ant_message[]?
the p_ant_message[]...
Is the recently released SoftDevice - ANT/BLE S332 SoftDevice v6.1.0 - compatible with the recently released SDK v15.2.0 ?
The supported SoftDevices listed in the documention...
Hello. A re-connection failure problem happens on our products.
chip:nRF52832 SoftDevice:S132 SDK v11.0
1. pairing and bonding on LESC 2. reset connection and re-connect...
Hi,
I have connected and SPI flash module to my pca10040 dev board. I wrote a test cycle of erase/write/verify for the entire flash and it works correctly. My initial pinout...
Hi,
I need some very simple file system to use on an external SPI flash. I gave a quick look at Flash Data Storage and it should be ok for me. I am not sure though why it...
Hi,
Disclaimer - this is definitely a question where one picture worth a 1000 words... ;)
My app use timeslot api to get a free time period to do some hard real-time...
