I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I'm developing a battery powered BLE sensor application where I need some basic guidance on how to implement this:
The sensor action consists of a measurement process where...
Hi there!
I appreciate your work on Nordic SDKs which are getting better and better.
But sometimes SDK setup isn't as quick as it could be.
E.g. for evaluation purposes...
Hi,
I am trying to port the Thingy project (ble_app_thingy_s132_pca20020) to Segger Embedded Studio on a Mac and it proved to be not an easy task, in fact I have hit a...
Dear all, I am building a BLE thermometer based on nRF51422 chip. I need to get certify it and if any of you performed and have the tests results of the below tests, for the...
The board came pre-programmed for MBED. I don't need that, wood like to enable regular JLink. I believe the process is to get it in boot loader update mode (hold boot/reset...
Hello,
I am new in this platform. Few days ago, my boss give me a nRFgo Motherboard. He want me to write a program that nRF24le1e can read/write data from sensor via I2C...
Just verifying to be 110% sure:
The TRACEDATA1-4 pins may be used as ordinary GPIO pins when no trace-functionality is configured for the debugger? So even if a debugger...
Hi,
I have a PCA10040 connected with some wires to an external I2C device and I need to poll data from the I2C device and send it over BLE, also updating the advertisement...
Hello,
I'm looking at the different way to control / dialogue with nRF9160 module.
I know it is possible to send commands through the UART port or through the cloud, but...
Hello Support,
I have developed one device based on NRF52,it has interfaced 4 sensors.It's working fine.
Now i want add one feature is that if sometime connection lost...
Hi,
I'm doing research on Bluetooth Mesh for which I built a Mesh system for testing throughput. So currently I am sending messages at the max speed (every 25 milliseconds...
Dear Nordic,
I am trying to do the following;
nrf52840dk will be ble central
ios will be peripheral
ios will begin to advertise then nrf52840 will connect
...
We are using SDK 15.0 and Softdevice 6.0, nRF52832
The question is :(1) We migrated the example "ble_app_hrs_freertos" to "ble_app_uart_c",luckily it works ;(2) But when...
HI,
I am using NRF52832,SDK15.2
I need to work on ultra low power consumption because My project related to Health care, Fitness tracker and HOME IOT mesh network.
for...
Hi,
I'm using the TWI master example to test my application. I wanted to extend the example to write into flash (fstorage module), in a way that I can transmit data over...
