I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I'm attempting to use a high-limit reached event from the SAADC to trigger the clearing of a GPIO. My wish is to disable this GPIO with the lowest possible latency...
I used SDK 13.x to create a custom profile with services for nRF52832 with BLE 4.2
If I go to a nrf52840 with BLE 5.x SDK, can I use the exact same code, or do I have to...
Hi, I'm currently trying to make a flash logger using the nRF51822_XXAB. I want to use as much space as possible in the flash storage for the logs. I will be logging a word...
Hey, there.
I'm trying to use the NVMC to give me some persistent memory. I call init first, reads seem to work fine, but writes just don't seem to work.
So to the best...
Hi team,
Today i received smart remote 3 kit.
one ready remote and other one is add on remote.
I can be able to update the firmware to using debugging pins to ready...
Hi
Let us say I wanted to integrate mesh capability into one of the existing GATT based sample apps - like say "ble_app_hts" so that I could publish the temperature over...
Hi, i have application with buttonless DFU and boot loader. I am able to upload distribute zip package to the board via nRF Connect and nRF Toolbox apps on Android . But the...
Hello everybody,
I tested the example: https://github.com/Rallare/nrf51_ble_app_hids_kbd_consumercontrol/tree/SDK11 on my customer board (and on the DK52) with the NRF52832...
Hi,
1. After studying about power profiling and application examples/ble_peripheral/ble_app_pwr_profiling, came to know that this example currently supports advertising...
Hi,
I am establishing a Bluetooth mesh network with nordic boards (nRF52 DK) having one provisioner and many provisionee devices. But I have one doubt, if I remove the...
Hello,
We are developing wearable which has NRF52 as main MCU. We are looking for suggestions to select proper sensors like Pedometer, Heart Rate Sensor and 128x32 OLED...
Device：Nrf51822
SDK：SDK12.3
Device name consists of "scanner:" and four digits。But sometimes the device name display error。An extra character appears in the device name...
Hi,
I've undertaken my very first custom Bluetooth PCB project, choosing an nRF52810 as the MCU of choice.
Having already tried and tested a SparkFun nRF52832 breakout...
Hi all!
Antenna that used in nRf51822 developement kit:
too big for my design, so I tried to use antenna that I copied from TI AN430:
There is devices that use...
