I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I cannot find my nRF52 (PCA100040 / SD132) when scanning for devices from my nRF Master Control Panel on my Android Phone.
In these two posts ( post1 and post2 ...
i have nrf51422 v2 that its compatible with sdk v6 and s110 v7
when i run the example of this sdk , only one phone can detect it and that is nokia windows phone
HTC and...
I have known that is AES-128 for the security solution on nRF51822.
We need more powerful security function and algorithm.
As this developer zone, Bluetooth Core 4.2 has...
We are using NRF52832, SDK 11.0.0.2 alpha, S132 soft Device ,I need some clarifications on using SPI,
In nrf52832 SPI Master driver is it possible to create two SPI...
I am evaluating the Keil compiler, version 5.18 with a Nordic development board (PCA100400) running the nRF52832
I just downloaded and installed Nordic's nRF5x-MDK-Keil4...
Here is the link to the image how we set it up: Click Here to See
We are getting a fatal error while running "Master Loop Back" example. We have also tried "SPI Master...
I use the nRF51 chip with a UART communication. I developed a protocol on the UART to communicate with another processor or a PC. Every messages of the protocol have 2 bytes...
I have an arduino connected to a redbear BLE shield.
the BLE shield uses nordic nRF8001 chip.
How could I implement RSC ? (running speed and cadence)
I would like to...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hi!
As a student, I am starting a new project on university. Project is based on beacons idea, so I decided to use Nordic's chip as an MCU.
I am trying to decide, which...
Hey folks,
I am going to join Nordic Developers community, but before I can do that I need your help.
I am quite familiar with software development, however, embedded...
Hello,
DFU issue (FOTA application update fail)
I have a problem when performing Application update over the air , after i change my boot loader.
so when try FOTA...
Hi,
I am using two Android devices with nRF Master Control Panel (BLE v4.0.5) app installed on both. I am using one Android device (Moto G 3rd Gen Android v6.0) as the...
Hi all,
I see that the nRF51 doesn't have a PWM module and a software PWM library is needed. How well does the software module actually run? I've had rather bad experiences...
