Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
I have met return error below point when I try to upload Application Hex file with bootloader in nRFgo Studio Ver1.17.0.3211.
if (!(IS_WORD_SIZED(m_start_packet...
I am trying to get enhanced shockburst working with the nRF24LU and the nRF5188. I am using the nRF5188 as the transmitter and the nRF24LU as the receiver. I am using the...
hii...
i hv maufature_array of size 7 to advertise.... am facing a problem while advertising battery level service with dat... my code is lyk dis
uint32_t err_code;...
Hi !
Here my adv setting (slow interval) to advertise every seconds :
#define APP_ADV_INTERVAL_SLOW 0x0664 /** This value corresponds to 1022.5 ms).
#define APP_SLOW_ADV_TIMEOUT...
Just ordered another pair of beacon hardware and noted the nrf chip is now coated in black goop.
Curious as to what this is for, and the reasoning its been added to the...
Hello,
I have a master configured as "Bidirectional Master Channel" and a slave configured as "Bidirectional Slave Channel". Both talk to each other. When I start just the...
Is the DC/DC converter enabled when running ble_app_beacon?
Or is it only the LDO that is enabled?
I am running the application on nRF51822-DK.
BR Magnus
I ran into this last night and curiously, James appears to have posted about it yesterday ( devzone.nordicsemi.com/.../trouble-with-system-halted,but-cannot-reset-nrf51822...
I am trying to get the Heart Rate example in the nRF51 SDK to work (found in ...nrf51822/board/nrf6310/ble/ble_app_hrs). It fails at line 338 in main.c (at the call sd_ble_gap_device_name_set...
I'm putting some bootloader and static config data in the customer section of the UICR and I accidentally wrote to 0x1001200 and worked just fine.
Looking closer, it seems...
Dears:
We will adopt nRF51822 for our project, and we want to confirm with you for the question as below:
Does nRF51822 support HCI command protocol through either...
Hello,
I do erase flash pages in my application I use the sdk api:
nrf_nvmc_page_erase(firstaddress);
nrf_nvmc_write_bytes(address, data, len);
but I did not found...
