Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
HI Devzone
currently my customer would like to get SRAM execution permission in their porject.
we found a config marco to set the SRAM permission " CONFIG_SRAM _REGION_PERMISSIONS...
HI,
i using 52840DK SDK17.2 s140 10056 test NFC pairing.
ble_central\experimental\ble_nfc_pairing_reference_c 10056 s140 ble_peripheral\experimental\ble_nfc_pairing_reference...
I am using
MF V1.3
NCS V1.6.0
nRF9160Dk V0.15.0
Project: AGPS Sample
If i set the Interval in the gps_config structure to any number under 240 and run the sample...
Hi,
We are working on nrf52840 in that we have some doubt how to test the radio tx and rx in datasheet you have mentioned
Active mode Tx Current - 4.8mA and 0dbm ...
Upgraded from v16.0.0 to v17.1.0 and have a truncation issue. It only occurs after the first send. Reverted back to v16.0.0 and all ok.
No other code change other than the...
I've searched around, but i couldn't find anything about how to use DMA with SPI master on a nRF5340 (and zephyr doesn't support DMA on nRF5340 right?). Can someone point...
Hi,
I'm using ble_app_uart to test AT.
When I sending a buffer
reset_buff[10]="AT+RESET\r\n";
RTT log showing an error
<error> app: ERROR 4 [NRF_ERROR_NO_MEM] at...
Hi all,
I'm currently trying to interface an nRF52832 with an external Flash chip via SPI
I have tried with both NAND and NOR types, specifically the MT29F2G01 from Micron...
I am trying to develop CAN communication using nRF52 dev kit based on nRF52832 (PCA10040) and a MIKROE CAN SPI click 3.3V board . This board has an mcp2515 stand alone CAN...
Hello,
I had RTT configured as the logging backend and it was working fine. When I enabled the SHELL on RTT, the log output stopped. Maybe more specifically, printk() output...
Hello there,
I'm trying to downgrade nRF Programmer from v2.0.0 to v1.4.11 as it is not possible anymore to select a Segger debugger as target device in the newer version...
Im trying to make a simpel project reading the sensor BME280 over SPI. I can´t get any activity on the SPI pins when i check with my logic analyzer.
I´m using nrf9160-DK...
I've based my code upon the HIDS keyboard example and added code to support an attached polled sensor with I2C interface. The device will pair with the Android phone just...
Hello,
I'm writing an application that sends cycling power information via ANT+ and Bluetooth (S340, on a nRF82840). While the ANT+ is a pure cycling power service, the...
