before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi
On my device, after a successful (bonded) connection to a central, if I then turn off BLE on that central, my device moves through fast advertising and slow advertising...
Hi
I am trying to get the SDHC/Disk access with FAT working on the nRF9160 dev platform and Asset_Tracker V1 app
It is shown to be connected on the TRACE connector ...
I have two BC805M EK .
Board 1: when I upload the (LED controlled by reset button) code to it, it works fine.
Board 2: when I upload the LED control code to it, I could...
Hi,
I want to build an application for nRF52840 DK that receives data through BLE from mobile phone (via nRF connect android application) and sends it to another microcontroller...
nrf51822 QFAC have more flash and ram than QFAA, so, is QFAC consume more electric current than QFAA in idle mode and sleep mode? in low-power consumption product，if it's...
Hi,
I want to configure 2 channels of saadc in differential mode as follows:
But when I received data, it seems that only the channel that its channel index is zero...
Hello,
1) In nrf5340 app CPU, there are only 3 timer I can use, timer0, timer1 and time2, is it right?
2) I want to use four timers in my project, to control two SPI...
Hello,
I'm seeing nrfjprog return with error code 33 when I try to program (or erase) an Adafruit Feather nRF52. I'm using an nRF52-DK as a programmer. The feather board...
Hi,
I'm trying to write/read from flash in my app. Reading/writing works until I either:
a) run ant_hrm_rx_start() - then after the call to nrf_fstorage_erase I get "00...
Hello!
I'm from Russia, my name is Anton.
I need a developer kit to research a real-time motion tracking system (RTLS) based on Bluetooth Low Energy, Bluetooth 5.1, Bluetooth...
Привет! Я из России, меня зовут Антон. Мне нужен комплект разработчика для исследования системы отслеживания движения в реальном времени (RTLS) на основе Bluetooth Low Energy...
I am trying to upload an image via BLE DFU, tested on mobile phone and Desktop (Windows) But I receive the following error after all packages have been sent to the device...
Hi,
can nRF52/nRF53 automatically fall back to LDO mode if DCDC enabled in firmware but with bad inductor connection on PCB?
Could re-flash the firmware to disable DCDC...
Hi everyone.
I'm developing a product with nRF5340 and zephyr os. But I found some problems about bluetooth dfu.
Because my application very big. So I can't use defualt...
Hi,
I am evaluating the use of nRF52832/52840 running ZephryOS HCI (Uart or USB) in combination with Bluez/Linux to as central device/gateway. If I were to use the Nordic...
