Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
A little backgroud for my project. The goal of the project is to be able to identify the proximity of beaconing devices in an area to a specific observer which then reports...
Hi, Below is the mapping of RAM on the 840 from the infocenter. We want to utilize the functionality to turn off unused RAM (via sd_power_ram_power_clr), but we see that if...
I am using SoftDevice s140v6.1.1. The behavior is I was able to program nRF52840 through JTAG without any issue. I am checking out the OTA firmware update feature and nRFConnect...
Hello Everyone,
I am developing one product using nRF52840 MCU, in this project my master controller is nRF52840 MCU and the host is STM-based MCU.
My goal is to make...
Hi,
I am configuring a test software to generate CW signals at channel 0, 19 and 39. Currently I'm using the nRF52840dk, later a custom board. The channel number is calculated...
Hi,
I have a product and want to update it with a BLE functionality. The product has EFM32 Giant Gecko MCU (ARM M3).
I want to know if it is powerful enough to run an...
Hello. I am writing a program using an example called ble_app_uart. While using the printf function, the output is output with a delay of 10us between characters and characters...
I try to integrate the Nordic pc-ble driver (Version 4.1.2 API 5) into a Qt application. I use the heart rate collector example to check how I have to integrate the library...
I have implemented all the models given in nRF Mesh SDK in nRF52832. Now I want to implement the HSL Model in nRF52832, for that there are no files related to HSL model in...
Hi all,
As I wanted to try out the new extended periodic advertising examples (periodic_adv and periodic_sync) located under /v1.5.0/zephyr/samples/bluetooth of the latest...
hello,
i am using nrf52840 with our cutomised board and trying to achieve long range using coded phy and using that long range demo example as base i have sucessfully changed...
I try to send out sensor streaming data to terminal over BLE NUS. Sensor sampling rate is 100Hz and 6 bytes per sample. Is there a best option to do this if I need to send...
We're working on a product that is able to store around 400uC of charge (two 220uF capacitors). There is a constant input of 21 uA minimum coming from a small solar panel...
I'm using AT%XRFTEST=0,1,2,19300,-40,1 to test reception at 1930MHz on the NRF9160 DK with a CW generator, and I don't understand the effect of the -40 parameter. With my...
We are currently working on an energy harvesting solution that powers the nRF52832. The energy harvester is providing energy from indoor solar and at the lowest light level...
