Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi
We've recently added FreeRTOS to the firmware of an existing product (primarily to pre-empt big chunks of 3rd-party code over which we have no control and execute them...
Hi,
As discussed, the instructed PCB land pattern for nRF9160 is according to Product Specification:
However, we have noticed that land pattern exceeds nRF9160 dimensions...
Hello ,
I am trying DFU over BLE.I am using SDK 14.0.2 .
i Flashed Bootloader Code and Softdevice 5.0.0 .then Device is Starting Advertised as DfuTarg and As Mention in...
Hello,
i have one nrf52840 board with a coded phy scanner and another sending advertisings, when it are close , i received in the scanner 100% of Advertisings, but when...
Hello,
I'm doing some initial investigation with the nrf9160 DK and after some reading and testing, it's clear that significant part of the low-power capabilities is determined...
Hi, I'm using nRF52 DK (nRF52832), demo code <TWI sensor>. I'm using this slave sensor to communicate with Master nRF52 DK. My code gets stuck at sensor_set_mode() function...
Hi,
I am trying to test the eligibility of updating my project from SDK 16.0 to 17.2 using DFU. I programmed just softdevice and bootloader of SDK 16.0 and made a package...
Hello All ,
I want to use timer 2 of nRF52810..my code is not giving any error but timer is also not going to IRQ handler...but if i made the same changes for timer 0 it...
Hello,
I'm using Seeger Embedded Studio and S132.
I'm trying to include ble_nus.h to ble_app template and compiling. But it gives this error:
2> In file included from...
hi,
I have following setup test cases .
Case 1 DK2 , DK1 Initialized with CLI directly
1a DK2 , DK1 Directly connected to CLI Every Thing Works
1b DK2-to-DK1-to-CLI...
Hi,
I am checking the voltage range on the input pins of the Nrf52832. The specs show VIH is 0,7*VDD and VIL is 0,3*VDD. I'm using the Nrf52DK, which has about 2.8V VDD...
Hello again,
This time I am trying to read HID reports using bluetooth to get the state of the caps lock.
I know this should be super simple and its explained in the hid...
Hello, dear developers!
Tell me the solution to the problem, how to properly initialize the SPI peripherals so that the program does not hang while waiting for the end of...
Dear All,
I'm using nrf52840-DK for development purpose of IEEE 802.15.4 standard. One is used as transmitter, while other as receiver. I'm using nrf_radio_driver inside...
