Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
hi ,
I am working on the nRF52832 , I am trying to store the values in structure and then passing over BLE . I am getting this error after print statement unknown function...
Hi,
I am trying to evaluate nRF5340 FOTA update via Bluetooth. I started with the Bluetooth/peripheral code sample as the basis for my project. I modified the project per...
Could you clarify the use of nrf_esb_set_retransmit_count function?
From what I understood, if it is 0 and it sends a message that wants to be acknowledge , it will not...
To setup the UARTE for use in Zephyr I've configured a nrf52840dk_nrf52840.overlay as Zephyr documentation suggests:
& uart1 {
compatible = "nordic,nrf-uarte"...
Hi, I'm setting up a timer to invoke (via PPI) the ADC in scan mode. It'll read to channels with MAXCNT of 10,000. The ADC built in timer has a value from
[80..2047...
Hi,
I can run the following code within main.c successfully, but it produces the error as shown in the attachment upon execution of k_free(mem.ptr) from with aggregator...
Hello,
in our project we have a nRF52840DK as Central and a custom nRF52832 board as Peripheral. The software on the Central is based on the ble_app_uart_c example and the...
Hi
We are using Nordic NRF52840 in our design. Normally we are using DCDC mode with VDD and VDDH together [Normal mode] connected to 2.2V. In a special case we wanted to...
Hi everyone,
I wanted to make reset pin funtional on nRF52 DK while using pca10040e folder so that I could develop on nRF52810 later, but the reset button did not work as...
I've noticed the idle current of my application changes permanently by ~5uA after using the radio, timer2, and/or the app timer (not sure which). I'm using a custom radio...
Hello,
I am using libUARTE and libUARTE ASYNC for reliable communication over UART.
I need to transmit data that is stored in read only memory but this module seems to...
Hi,
I'm trying to use flash FDS on 10040-Dk with softdevice s132 and freeRTOS.
I debug the code using segger embedded studio, when executing a write to the flash It reaches...
Hello,
we want to support scan for both 1Mbps and Long Range beacons and we are using the S140 6.1.0.
This is the configuration for the scan parameters:
When this...
Hi all,
DFU package V1_0_75 was developed using SDK12 for nrf5232 and V2_0_45 was developed using SDK16 for nrf5232.
I am trying to update from V1_0_75 to V2_0_45 using...
