I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello.
I'm running the nRF5 SDK's ATT_MTU throughput example.(nRF5 SDK v15.3.0, nRF52 DK(nRF52832))
The tester is running as a central or peripheral device.
How to operation...
Hi nordic moderator team,
I'd like for you to reopen this thread https://devzone.nordicsemi.com/f/nordic-q-a/51673/nrf52832-sd_ble_gatts_value_get-or-catching-ble_gatts_evt_rw_authorize_request...
Hi,
I am using APP UART for Communication with slave device, the data transmission between two devices like send a command and get the response,
while getting the response...
Hi,
I faced a problem while building my project. Please see screenshot below
I think I have already include all the files and everything compiled. But this error shows...
I am trying to run smart remote 3 on PCA10040/nRF52832.
I use gcc makefile to generate PCA63519-SR3_nRF52832_Shield firmware. SD firmware is downloaded by jflash and I use...
Hi,
I want to update firmware on nrf52832, but I have an error: DFU insufficient resources
I found this and this , so I try to program my softdevice with this file: /nRF5_SDK_15...
Hi，
there is a issue very strange, on a nrf52832 project, it use two gpio set to sense low level, one is p18, one is p29, I found there is no response for low level of p29...
We are using nRF52832 with SDK_15.3.0 running the Nordic UART service (NUS) example.
Out of the box we find that the uart event handler is continually being called with...
Hi,
I have an SPI peripheral on pins 26, 27, 28, 29 which I'm able to override the default system's UART0 pin assignments in nrf9160_pca10090ns.overlay. However when I enable...
Dear sir,
We have interfaced a charger ic with NRF52832. It is having a charging status pin to show completion of charge. It is having 3 states
1. High impedance (Battery...
Hello guys,
Something strange is happening here and I need your opinion about that... I have a custom board with nRF52840-based BL654 module on it. I am using SDK15.3.0...
Hello
I am using nrf52840 chip. I am having trouble configuring SAADC to read analogue input on two channels (one signal is VDD of the chip). I have already searched the...
I am trying to get connected with my Android App and I have noticed that sometimes when the user turns off Bluetooth and tries to enable it again after 20 minutes my Android...
I am working from the ble_app_hids_keyboard example. To support multiple centrals, I imagine the first step is changing NRF_SDH_BLE_PERIPHERAL_LINK_COUNT and NRF_SDH_BLE_TOTAL_LINK_COUNT...
