before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I am trying to flash my custom board that uses the Raytac nRF52840 via SWD. I am trying to flash a custom bootloader onto the chip; however, JFlash is giving me an error....
Hi, I am from China. My company made a BLE module with chip nRF52810. Recently , I coded a program for it by SDK12, based on ble_app_uart example. I modified the corresponding...
Hi there, I'm using nrf52840 with OpenThread SDK and I wanna know, what is default radio mode of this device? Because we also have another project with Bluetooth and we observe...
SDK15.0 whitelist hardfault
when setting the sd_ble_gap_device_identities_set using the iOS nrfConnect the non DK board hardfaults.
On an android device all works fine...
Hi,
I'm adding some custom buttons to the NRF52-DK and I've been playing around in PCA10040.h. So far, I have everything working with 4 buttons. The DK can connect to...
Dears,
Now I am using nRF5_SDK_15.3.0_59ac345 for my project on nRF52810.
I found a bootloader example at
\nRF5_SDK_15.3.0_59ac345\examples\dfu\secure_bootloader\pca10040e_ble...
hello, I am trying to integrates saadc & bluetooth because in my project adc sample values are comming from sensor & these values is send through bluetooth_uart app. so can...
Hi,
I'm in the process of evaluating the nRF9160 DK and this I want to be able to control the diferent peripherals on the DK so I can reduce as much as I can the current...
Dear supplier
I want to read 10 heart rate sensors that are connected to 10 person's bodies and then display them on TV. How can I do it?
Can I use nRF52832 chip? Can...
Hi
I am using nRF5_SDK_15.2.0_9412b96 on pca 10040
I am storing over 2000 ADC readings and then printing them out once my test is complete. I get "Logs Dropped(x) " messages...
Hello
I am writing a program using SDK 15.0.0.
I'm trying to merge SPI and TWI programs into BLE programs.
I used keil before to confirm that each program was working...
Using Ozone v2.54, if i halt program execution and then resume again, I get a NRF_FAULT_ID_SD_ASSERT fault, with info = 0, pc = 0x142CA.
softdevice: s132 v4.0.2
The error...
Hello ,
I am using Multiperipheral example code , and i want to connect more than 4 central devices. I have edited the link total value and number of peripherals and centrals...
HI,
I am recently working on 9 axes icm 20948 sensor. my battery capacity is small for the application and my accelerometer and gyro sensor consumes more current.
when...
