before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
I use nrf52832 sdk15.2 to develop products, use WDT to prevent program crashes, WDT set time is 10S, nrf52832 will be paired and bound after connecting with IOS phone, when...
Hi!
I am trying to use the SAADC driver on SDK13, following some examples from the playground repo. I am using the app timer to trigger a measurement for 4 channels. ...
Hello,
I cant seem to find a PBKDF2 function in the SDK to generate a private key from a passphrase.
We want to use mbed-tls or CC310 to make a SHA512 based key for AES...
Hi Everyone,
I have a custom board with nRF52840 and am testing out basic GPIO functionalities with some LEDs. In the board, the LED cathode is connected to nRF52840 GPIO...
Using nRF Connect for PC Version 2.6.1
Connect to a peripheral device that ask for an ATT_MTU > 247 bytes
NRF Connect fails with
Failed to call gattsExchangeMtuReply...
Hi
I have implemented (heavily base on the found examples) an application which uses both ESB and BLE. For now I focus on developing the ESB part of the SW. I am using the...
Hi Sir,
According to the nRF52832_PS_v1.4.pdf, In section 17.1.1, the table shows the current consumption of Radio. What's difference w/ Iradio_tx0 and Is0? Why do we get...
Dear Nordic Team,
We are building a very low power wearable with the nRF52810, only powered by a small solar cell and a super-capacitor.
We would like to offer firmware...
Hey,
I am working on nRF52 DK boards. Suddenly PC is not detecting the one of my DK board, but the nrf53832 processor's LEDs are functioning as per the last program dumped...
I am trying to use multiple channels for beacon transmission.I want to hop to a different channel at an interval of 2 seconds.I have configured one device as a pan coordinator...
Hello,
I'm using following code to read two channels of SAADC. It works fine when device is not connected to BLE central device. As soon as it's connected, the saadc_callback...
Hello,
I want to use 2 thingy:52 board in which one will act as master and other as slave. If yes, how can we do it? please provide any example code. Thank you.
hi guys, I'm looking for understand how to send a simple signal using ble mesh between two nrf52840 boards.
The available example aren't so usefull in order to have the...
I need to store a data base into an area of the FLASH. I understand I need to use the pstorage capability. All the reference I found about it , are just part of the code where...
Hi, I bought Sparkfun nrf52832 breakout board and i am having issues with programming a board.
I downloaded Segger embedded studio and nRFGo Studio for uploading hex files...
