Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
hi ,everyone
HOW TO do a DFU by myself serial protocol in mesh network ?
0.I know it can scucess through a python script in PC (even thougth i try failed to run this example...
Hello,
I want to develop a ANT+ product, example rope skipping or Dumbbell, but i can not find out these ANT+ Device Profile.
How can i do? Can i use a personal ANT+ Protocol...
Hi, I am working on SDK 15.0 Multilink central and Multi peripheral
Soft device: 6.0.0
Segger IDE
Application overview :
When the central request to all peripherals...
Hi, I have seen in other topics here that it is not possible to control the server of the light switch example from the Android App, only the Generic On Off Model. But when...
I am working on RTLS project using nrf52832 SOC. In beacon mode i want to advertise temperature and battery strength . but i am not sure if what method should i use to measure...
Hi,
I am using nrf51822 in my project.So we are using keil5 u vision project and sdk 12.3 version so here the problem is i have imported the example program from the sdk...
The nRF52840 supports 2 Master/Slave instances.
Is it possible to configure the nRF52840 as a Master when connected to an I2C bus that has another Master present?
SDK 15.2, S132 6.1, nRF52832
I have a characteristics to write data to a peripheral, using variable length up to 507 bytes and authorization.
Writing to the peripheral...
I'm using nrf_fstorage_wrile() which work fine on most of the cases, except for len == 6 bytes. When I read back on the Flash, after successful write, I found that only 6...
Hi,
It‘s great thing that the nRF9160 DK can buy.
But there are few question need to be confirmed?
1, I saw the "Onging ceretifications" ( https://www.nordicsemi.com...
Hi,
I am using a nRF9160 with the LTE-M modem firmware. But I want to change it to the NB-IoT firmware. I have followed the instructions to install the dfu.
But when I...
Hi
I am looking at the file
\examples\light_switch\server\light_switch_server_nrf52840_xxAA_s140_6_1_0.emProject
and in there I see that there is the line
linker_section_placements_segments...
Hi,
We are planning to develop an IOT device using the nRF52840 which will communicate with a Hub device which will contain another nRF52840 chip, so we want to check the...
Hello,
I am compiling with encryption implemented for Bluetooth communications. Specifically with code taken from the ble_app_hrs_c example.
I am seeing this error:
...
