Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
I'm using nRF52832 on a custom board and I have tried to run sdk example nfc_url_record, but it doesn't work.
I have tried to find solution among existing answers...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
Hi,
Referring to this thread -
If the saadc sampling is trigger by a timer (through ppi), what is the correct way to saadc_uninit() without using the global m_sampling...
Hello,
nRF52832 datasheet denotes saadc sampling time in scan mode (paragraph 37.5.4) as:
What is extra time it takes for the easyDMA to store the samples in RAM ? ...
Hi Nordic.
currently i am working on nRF52840 as a reader and after designing as per your recomendation and it is ready to check but whe i connected to the commander the...
I have loaded the HEX file of nRF_Sniffer_200_beta3 to my nRF52832 or nRF52840 board, it can not be run as sniffer. May I know how to use my own nRF52840 chip as Sniffer?...
Hey! Is there a way to multithread the nRF52832? I want to store data in the buffer and do some processing on that. While processing I want to control how the data is stored...
We need to compare the signal of nRF51 dongle with our product.
How to find nRF51 dongle(nRF51422) with hciconfig in Linux?
firmware: PCA10031 1.1.0 2018.39
Guess I...
Hi,
Can you please direct me to the document that explains about generating more than 8 bits of clock in SPI and keeping CS line low for that entire period.
Also, if...
I've been working on a project based on nRF SDK. The project is developed in C++14/17 and I found that nRF SDK 15.2.0 doesn't always want to compile with C++ compiler. I made...
Hi I'm using the nrf52832 and want to send datas via UART and SPI but the PSI example Show different Settings of UART then the BLE_APP_UART. The BLE_APP_UART is running well...
We are currently developing our product in Zephyr using the BLE Host/Controller with virtual HCI (building the project with . We are anticipating a Nordic Zephyr BLE solution...
Are there any native RTOS build-in the SDK? If I need to develop a sensor device driver (i2c based) any recommendation as the safest way to do that. Choosing between freeRTOS...
