Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I was working with the buttonless DFU service that requires bonds and I was able to update my firmware just fine. Then I added Just Works OOB pairing using the nfc_ble_pair_lib...
Hello,
I am in big problem, just couple of months ago i managed to run dfu over BLE mesh. Even now its working in windows platform but for some strange reason its not working...
Hi,
I use dongles with custom application that combines Thread and CDC ACM. The application works fine, but after restarting PC several dongles with this application stopped...
Hi,
I have a smartwatch that has a nrf52832 chip inside. It firmware runs on S132 SoftDevice ver 2.0.1 and has an OTA bootloader which supposingly allows me to upload firmware...
I am evaluating the nRF5284 SDK 15 Module in HCI mode. I am trying to scan Extended advertise when: 1.Extended non connectable non scannable advertising, Primary_Advertising_PHY...
Hi,
I have just purchased a nRF52840 usb dongle ( https://www.mouser.in/ProductDetail/Nordic-Semiconductor/nRF52840-Dongle?qs=gTYE2QTfZfTbdrOaMHWEZg==) .
I would like...
Hello, I am a beginner and I just got a Raytac "MDBT50Q" bluetooth 5 module based of nRF52840 Soc.MDBT50Q does not come with a builtin frimware to respond to AT-commands.Can...
Hello, i have this problem with DFU, in Mesh SDK v3.0, i am using PCA10040.
this is my boodloader_config_default.json
and i am using this for make the pkg.
and...
Hi!
For our development purposes I am implementing NRFUTIL 0.3 for mesh on Android/Java, migrating it from Python code, via UART/Serial, for DFU purposes
It looks like...
Hello,
I am having difficulty using a single TWI to support a DAC (MCP4725) and IMU (BNO055).
I am using nRF52 DK, and SDK 14.3 with the SEGGER IDE. The DAC is running...
Hi,
I am trying to run lte_ble_gateway sample on nrf9160 DK, but in debug I can not catch breakpoint on main().
When I going in debug mode step by step I find that the...
Hi
I am new to the NRF52840. I am trying to receive data from nrf24L01+ to the nrf52840 Development kit. I find some examples from the SDK radio receiver using PCAl0056...
Hello all：
I am using nRF52-DK（pca10040）to do some tests.
I want to use gazell and at the same time, I want to detect the events of the NRF_RADIO, connect it to PPI. ...
Hello,
I am using Eclipse to create a project using code from ble_app_hrs and I am developing for a nrf52832 chip. Unfortunately, I am getting a "was not declared in this...
I send a sequence of characteristic writes to my device, in code based on the nRF Toolbox. Sometimes I see this error message. Why does it happen and what steps can I take...
