I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi all ,
I using sdk12.3 experimental_ble_app_buttonless_dfu project to development , below is my bootloader and project ram setting:
if I don't download the bootloader...
sdk12.3.0 In the ble_app_hrs_rscs_relay example, I added the uart_init function referring to the ble_uart example, but when I execute the APP_UART_FIFO_INIT () function, a...
My development environment is PCA10028, SoftDevice 130, SDK12.3.0
Two nRF51822s were mounted in one board One nRF51822 will be used as a TWI master and the other as a TWI...
It is said that ble5.0 can cover a range of 300m, I wonder how big is current when this is achieved? For 52840, the largest power output is 8dBm, for 52832, the largest output...
Hi,everybody!
I use nRF52832,supply volt 3.0V normal, program can be downloaded , run and debug,i ensure the program is accurately.To control a gpio P0.09,on the hardware...
Dear Nordic,
I debug the SDK15 example project ble_app_template_pac10056_s140 project, nothing change, but it will jump into app_error_weak.c as below picture, please help...
I can not get information about the power consumption when twi is enabled and idle. It just state the current when it is running. So do I need to disble it when it is idle...
Greetings,
We have taken the RAM Retention example and are experiencing a failure (all LEDs on) when setting MAX_TEST_ITERATIONS to a value greater than 1. This is duplicated...
I am using nrf51822 with softdevice 7.3 and sdk6. I am having some strange problems in single bank bootloader. The nrftoolbox version 2.4.0 gets stuck at 94% during the firmware...
Hi,
(SDK v14.2, nRF52832)
I'm developing a Timeout Timer functionality, and was wandering if the following scenario is a good practice:
I don't want to have a interrupt...
Good morning everyone,
I am having a lot of problems configuring the Peer Manager.
I read several discussions on the topic, but either they are old (referring to ble_evt_dispatch...
Hello everyone,
I`ve 4 thingys and ran the https://github.com/NordicPlayground/Nordic-Thingy52-mesh-demo . That works well.
Now I`m trying to add the nRF52 DK as a Node...
I am trying to perform a dfu upgrade according to: infocenter.nordicsemi.com/index.jsp
The exact command I am running is: nrfutil dfu ble -ic NRF52 -pkg dev_board_bl.zip...
There is something I want you to tell. Do you know how to allow other interrupts (specifically IRQ pin) while interrupting app_timer? I studied variously, but I can not find...
