Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
using nRf52832 with S132 in central mode
Scan-Interval= 3000 ms
Scan-Window= 25 ms
Monitoring the current consumption I see a 25ms wide pulse, as expected.
No advertiser...
Has anyone ever used nf51 bluetooth with the app inventor?
I have values coming out of the microcontroller terminal. I want to send them to a mobile application using...
I've got a few questions regarding memory of nRF51DK.
I would like to know what is the total memory size of the nRF51DK board?
What is the memory size allocated...
It looks to me like ANT_STACK_CONFIG is redundant in SDK 14.0.
nrf_sdh_ant_enable does all the same setup plus, it looks after all the new softdevice handler stuff.
...
Hi,
When I use nrfutil to generate a zip package, there would be three document in the package. Is there anyone know what does .dat and .json document use for? Could I...
Hi there,
I am begineer for nrf51822 and I want to interface MPU6050 WITH nrf51822 so can somebody provide me the tutorial with full detail.i want to read just raw values...
Have been following the nordic tutorial to update characteristic value using hvx_params. Currently the structure for hvx_params is as follows:
/**@brief GATT HVx parameters...
Hello every!
I am working with ATT_MTU_Thoughtput example (S132). My purpose is send data from "sever" to "client" and wait until "client" response to confirm . I was send...
I’m debugging the ble_app_blinky demo on a nRF52840-Preview-DK board (BOARD_PCA10056, S140). The device name in the debug configuration is nrf52832_xxaa.
Each time a breakpoint...
Hi all,
i use a nrf52 and in product specification i find the table about the low power mode and their consumption . Capter 17.1.
ION_RAMOFF_EVENT System ON, No RAM...
Hi all,
I have been playing with my PCA10040 and I came across the problem. I thought that it was a softdevice problem, so I went to bootloader mode (by connecting with...
Hi,
would it be possible to have multiple GAP Addresses for one nRF device? I was able to have this with the S130/S132 using verison 2.0.1 by using gap_address_set and...
Hi,
I have nRF52840 dev board which was detected and LEDs were coming on.
I tried programming the prebuilt throughput hex file in nRFgo Studio.
C:\Projects\NORDIC\nRF5_SDK_14...
Hello dear sir/madam, i have just started with BLE using nRF52832 DK .but i am not able to understand the examples.and don't know how to make any change.what is the basic...
My nRF5x DK kit has suddenly stopped working and I experience one or more of the following symptoms:
My kit doesn't show up in my computer.
LED 5 on my kit doesn...
