Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
We're encountering a frequent but intermittent hang after handing off OTA DFU to iOSDFULibrary 3.1.0. In the happy case, the characteristics are discovered and DFU process...
We are using the Android nRF toolbox v2.4.0 and have successfully implemented the Template app. The app will reliably connect with our device and functions well. The only...
Hey,
I was on one of the meetups when nrf52 was presented. You guys used a mbed shield for demos. Do you have code example and what pins you were using for connection?
I am working with the PCA10028 board, SDK 10.0.0, and s110 8.0.0. I have created a characteristic that is "coupled" to LED2. When a connected central writes a value to the...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hi, All!
I am using nRF51822QFAA with 16KB ram, and S130(sdk 11) for the dual bank bootloader, reference to the s130 releasenote, I config the ram memory start at 0x200013d0...
Hi,
I have tested several BLE examples in SDK12.30 and they would not compile, what's the problem?
for example here is the output of ble_app_uart example.
*** Using...
Hi,
Using this doc it says the SPI supports 16 bit frames. Is this true for the nrF51822 BLE Nano? I found that the mbed API does not support 16 bit frames doc . Can I...
Hello,
I tryed to find in Q&A something that can help me understand how it is possible to measure battery voltage with nRF52, but i am not sure i found the exact explanations...
The v3 reference manual of the nrf51 mentions:
"[The powerfail comparator] also provides hardware protection of data stored in program memory by preventing write instructions...
If I use the interrupt handler to set Flag, and read sensors and write data to SD card in the main loop as in the following code then everything works well.
#include <Wire...
What hidden settings am I missing this time in the awful Segger studio ?
I get an error :
unknown type name class
When I compile with this new class called...
hello i am new to spi, i am doing project on 3 wire spi interface. I am using 3 wire interface as Sclk,ssn,MOSI pins only , I am not using MISO pin .I am tested spi example...
