My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hi
I set the time and date from cfs
the received package is valid. the timestamp is transfer to the set method correctly. the output shows also that the system time is...
We are currently using a Linux system and controlling HCI_UART firmware through BlueZ.
The problem we are encountering is that using BlueZ V5.55 allows normal Bluetooth...
Hello! I have a GATT Server in the form of a nrf52840-DK that has been given to me from a company that has a custom service on the server using CCCD. I have the full documentation...
Hello,
I would like to know if using a self made GATT Custom Service in HID Device (NRF Desktop App) can incur additional costs during the Bluetooth qualification process...
Hi,
I am working on a project using the nrf52840. For legacy reasons we are using Nordic SDK version 15.3.0 and SoftDevice S140 version 6.1.1.
I am trying to maximise...
I need help . i am confused that if we send the audio data then it follow which of the following order ? input ->BLOCK ->FRAME->LC3CODEC->SDU->PDU OR input-> BLOCK->FRAME...
We need to establish connections to muliple of our products (they use nRF52832/nRF52840) parallel from our Android/iOS apps to send commands which are time critical (in relation...
Hi,
I am getting an error when trying to enable the Fast Pair (SDK 2.7.0) using the bt_fast_pair_enable() function.
I debugged this error and I saw that it's caused when...
Hi,
I am developing an application which needs a precise reference clock of 20ms. I have a 32MHz Xtal on the PCB with a tolerance of +-10ppm. To configure the device to...
Hi
I'm using nrf toolchain/sdk 2.5.2.
Got a strange problem with my QSPI NOR flash interface. when i run flash_erase i get error message "qspi_nor: Failed to schedule...
I am running a nrf5340 with zigbee as a coordinator, I observed after a while that battery life of my end devices don't last as expected. Then after debugging I found that...
Hi Team,
We are developing a custom board using nRF52840 SoC. We need the storage and handling of IC, reflow solder profile of IC and assembly instructions if any.
Regards...
HI currently i am utilizing sdk ver 17.1.10 nrf52840 s140 we are using dfu/secure_bootloader/pca10056_ble app and i need to add UART app to it so that so we need both bootloader...
hardware:nrf5340+npm1300
software:ncs 2.5.1
hi professor,
If I just connect VBUS, The npm1300 will reset when I read bulk register. If I connect vbat and vbus, read...
In NRFX Oscillator header , accessing the function requires the preprocessor macro which in turn requires preprocessor conditional
The problem is that final conditional...
