This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
I have implemented a Peripheral on an PCA10040 based on one of the SDK (v15) examples. When using nrf Connect with a nRF51 dongle I can connect to the peripheral and interact...
Hello !
1. Do you have examples for nRF52840 what is demonstrate encryption/decryption packets on the fly as it explained in PS chapter 6.4 ?
2. What about examples for...
I have a Jtrace which I use over ethernet.
Running nrfjprog shows:
nrfjprog -f nrf52 --eraseall ERROR: No debuggers were discovered. NOTE: For additional output, try running...
hello, im using nRF52840, pca10056, I was using the example ble uart from examples\peripheral\uart im planning on replacing the use of "putty" PC application with a program...
Hello, i did my own custom board with a nrf52805 and now I did one custom first she is working fine so I decided to do the same but I can't see my device in nrf connect app...
Based on the "system_off" example, I intend to use the RTC to wake the device up (a NRF52840) periodically every minute.
I setup the RTC with LFCLK (32KHz) to trigger a...
software: ncs v1.8.0
hardware: my test nrf52833 board, with 9 antennas.
I do experiment like this:
aoa rx: in "nrf52833dk_nrf52833.overlay" file, I set " dfe-antenna...
Hello,
I am trying UDP sample with a local SIM (Orange) to check eDRX settings following this ticket .
Carrier said i should set an APN. This was not needed with 1NCE...
I try the new save to CSV feature in v3.4 power profiler.
I try to save all, but it says 0MB.
The sample rate is 100ksps, and duration is 301 seconds, but would result...
Hi, I have the following code in main.c:
If I initialize the beacon advertising first, which is the shown configuration, I get fatal error code 8 out of ble_advertising_start...
I have recently updated the SDK for my application from version 13.0.0 to 17.1.0, everything seems to be in order except for this function in nrf_drv_twi.c called twi_clear_bus...
the updated version of nRF connect v3.8 , for desktop , app - programmer doesnt recognize the device . i downgraded to 3.3v this version selects my device .
Hello,
I have developed a Thread network based on SDK for Thread & Zigbee v.4.1.0 and OTBR image provided by Nordic. I recently upgraded my OTBR from a Raspberry Pi 3B+...
Hi, I have added libuarte example in-app template and sent data from Arduino to nRF52840 successfully. But after receiving some data and I am getting the following error....
