This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hello. An LED is connected to the pin of my nRF52832 through a resistor to ground. How can you programmatically determine its presence? I tried to do pullup and read the port...
Hi,
For the first time iOS App interface with BLE device. But after killing and re-opening of iOS App connection not established. Can anyone share me the code from iOS App...
Hello,
I would like to know wich step I forget to do to send more than 20 bytes in NRF Connect app to a BL652. I followed some talks and subjects about it but it's doesn...
I am using ble_app_uart_c example to scan nrf beacons. Facing strange issue with debugger.
Enabled RTT and disable UART Logs, when i connect debugger and put break point...
Dear, I have bought the nRF5340 DK. I have installed nRFConnector and Segger Studio. Now, I want to test Blinky project. I connected a USB cabel to USB connector which is...
I have a receiver , transmitter application. I use a custom board as transmitter. I would like to use pca10040 as receiver but currently i use it as debugger to my custom...
Hi,
Our company has produced a batch of BLE products, and the 10uH inductor model used above is SDFL2012S100KTF. The rated current is not as large as the current value...
Hi,
I close the uart log and open the rtt log
why uart log can be used still?
why rtt log display error state?
I set the log config like this:
I set the test...
hi
i have this error
.\_build\nrf52840_xxaa.axf: Error: L6218E: Undefined symbol app_timer_cnt_get (referred from max30105.o).
in this code part.
the example is...
I have a program that runs great on the dev kit, however after uploading the code to a custom board based on the nRF52810, it does not seem to run.
I upload the code by...
Hello,
I need to connect a custom I2C device to the nRF52-DK, and I am using the sdk v1.6.0-rc2.
I am new to this development environment and I don't know how to initialize...
What is the max nb of periodic advertisers that can synchronize to a single receiver?
The bt_le_per_adv_sync struct defines a uint16_t sync handle so I infer that at least...
I am using the following example to load the code with Segger debugger and it works.
nRF5_SDK_17.0.2_d674dde\examples\ble_central\ble_app_blinky_c\pca10040\s132\ses
Now...
I noticed that when a BLE client disconnects and then reconnects to the, instead of receiving all data arriving over the UART from nRF9160 to nRF52840, there is a delay of...
Is it possible to perform two TWI Consecutive reads without sending the stop bit in between?
Example: Read 1 Byte - represent length (xxx) of data to come with second read...
