I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hello, I have a time critical project that requires a unique service routine, thus a specific 128 bit UUID. I am following the tutorial on custom services but it does not...
I need to make something like this and need that baudrate which are configurated in smartphone BLE app that this value be and on NRF528XX uart baudrate.
For example when...
What is the recommended way to flash firmware onto the stand-alone microcontroller. I have never dealt with a stand-alone microcontroller before.
Vineet Nadella
I am trying to get buttnless DFU working on the NRF52832_XXAB which only has 256K Flash and 32K RAM.
I have buttonless DFU working on the nRF52 DK which has the larger part...
The above is the waveform of data pin and chip selection pin.（The yellow waveform is the data pin waveform. The blue waveform is the chip selection pin waveform. And chip...
Below is a picture of advertising event current waveform:
The TWI current consumption is upto 2mA, I change the peripheral from TWIM to TWI, the current is exactly the...
We are developping an application using an NRF52840, Based on nRF5 SDK for Thread and Zigbee V3.0.0
Running S140 softdevice
We are using BLE advertizements and Openthread...
I have a custom board with nRF52840 and uses Segger EDE.
In our project we would like to store some info about production to flash memory (DeviceID, production date etc...
I followed the guide Configuring and performing DFU over Mesh ,old firmware was examples\dfu\build\dfu_nrf52832_xxAA_s132_6.1.1_Debug\dfu_nrf52832_xxAA_s132_6.1.1.hex,new...
Hello,
I want am use NRF2401L01 for sending data wirelessly from one device to another device and vise-versa.
The First device is arduino nano(Transmitter) which senses...
I looked at the following question
nrRF2 GATT attribute read callback
and it does not quite answer what I want to know.
What I need to know is do I get signaled by the...
I have followed the getting started, with my new nRF52840DK, with switches at:
Sw6 Default
Sw8 On
VDD selected
when plugged into the USB, LED 5 blinks rapidly, LED...
Hello.
In order to connect multiple units on the previous question page ( https://devzone.nordicsemi.com/f/nordic-q-a/51970/implementing-multilinks-on-multiroll-programs...
