Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
Dear nordic:
I am confused of NRF51824 MTU issue, NRF51824 can use S130 softdevice, S130 is qualified bluetooth 4.2 core spec, then why S130 features don't included MTU...
While trying to find out a realistic maximum power consumption target I was searching for the power consumption of the LPCOMP comparator. I've seen a few claims about 0.5...
Hello,
I want to send data from central device to peripheral device. I am currently using nRF52DK.
While sending data from peripheral to central device, data is sent successfully...
hello all,
I buy the Fanstel EV-BC832 V2 and start to paying with it.
I used the IAR ide and Embedded studio (SEGGER) ide for my tests.
First i check the blinky and...
I development nRF52832, I want change mac address.
So I modified nRF5_SDK15.0.0/examples/ble_peripheral/ble_app_uart.
I added code to the examples.
////////////////...
Hi everyone,
I want to program the nrf51822 module with the discovery board stm32f429i-disc1 through ST-LINK programmer in Keil IDE but this error appears: "ST-LINK connection...
Dear DevZone Team,
I am an absolute beginner in the field of mesh networking and hope you could help me getting started. Please bear with me.
I have a bunch of sensors...
Does anyone uses Sloeber to program nRF52? I have an issue, when I add a header nrf_temp.h to the project and using following functions:
The problem appears when I add...
Dear Nordic team,
We are developing a BLE application for IOS and Android. On Android, we utilized your Nordic Scanner Lib to scan Bluetooth devices and it is fine and...
Hi. I am trying to stop advertising after a delay in the UART example using;
sd_ble_gap_adv_stop(???)
What do I put in the brackets? It is asking for a uint8_t called...
Hi,
How to stop freeRTOS xtask using timer and recreate again when needed? I'm currently want to control the blink interval, for example I want to have the led blink for...
I used sdk15.2.
The peripheral sends the public key to the central.I received an exception to public key processing.
code:
case BLE_BITBUTTON_C_EVT_BITBOTTON_M_NOTIFICATION...
Hello Everyone,
Struggling with evaluation of Secure DFU over UART lines. I used the sample project "Secure DFU Bootloader over Serial Link (UART/USB) ", during the previous...
Hello -
Any advice on finding a connector from a standard NFC Antenna to the Molex 051281-0594 connector on the Nordic Thingy:52 Board?
I am trying to find a larger NFC...
