Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
Hi Sir
I enabled the "APP_UART_FLOW_CONTROL_ENABLED", but I measured the CTS / RTS pin always is low during data transmission.
Is it normal ? How to check UART FLOW control...
Hey, i have got UART work on my Thingy52 with ANA/DIG0 and ANA/DIG1 as receiver and transmitter but when I am trying to use EXT0 and EXT1 as receiver and transmitter it doesn...
Hi,
I am new to embedded device development and I am wondering if I could get some help on SPI control from nrf51422/51822 chip with dev kit to AD9837 wave generator. I...
Hi,
I am try to create a PWM output which can move the specified number of steps.
Please find following source code
After I execute above problem, I can get following...
Respected sir,
There is added external reset button at SRU532 module, and changes are given according to it using wakeup button at code.When wakeup button is used then some...
Hi all,
I am trying to implement a multilink central with UART. I had looked through the forum on all discussions in about this and followed this thread to come up with...
Hi guys,
I'm testing the 52810 duf function.
hardwar: 52810
using SDK: 15.3.0
softdevice: s112_nrf52_6.1.1_softdevice.hex
download software: nrfgo Studio
bootloader...
I am trying to flash the blink example from SDK v15 into my custom nrf52840 board, I am using pc10056 example.
I connected my ulink2 to swdio, swclck, gnd and vcc of my...
Hi,
Since the last update of the 'Getting Started Assistant' (0.9.0) from 'nRF Connect' 2.6.2 on Windows, I can´t set up or compile any sample of the SDK for the evaluation...
So I've been having a problem the last few days - using the NRF52832 we have an SPI chip connected his chip requires a clock signal (1MHz) that is being generated by the NRF...
We have written code based on SDK V12.2 and found it doesn't support power saving mode. Given that it's very complicated to transplant to higher version, how can we fix the...
Hi,
I want to interface two QENC with nrf52840, I saw QDEC example and it works as expected.
The problem I am facing is that QENC has four pins of which two are for power...
Hello,
I am having strange issue. I'm getting some data from custom service and characteristic. I can see the data being received is correct. However, if I try to pass the...
Is there a set date for the release of a tracker SW with working GPS? And secondly, will there be a step by step instruction how to upgrade the software on the dev. board...
Hello,
I'm an Embedded system student and I would like to make an extension for ZigBee for which I need to make changes to the underlying ZBoss stack.
Is it possible for...
