Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hello, I am using the nRF51422 Development kit with SDK11. I am using the proximity application for the battery level service. I would like to strictly advertise to a single...
Hi,
I have an application where I have for example 5 BLE transmitting devices . Each device has one push button and each device is assigned to a number 1-5. I also have...
Dear nordic,
I am new in this open thread i tested your examples its working fine. i also tested CLI example i think its working but i didn't see a response in terminal...
I have a few Bluetooth transmitters based on nRF52832. My receiver devices are mainly iOS and Android mobile devices. I'm considering of replacing them with nRF52840 for Bluetooth...
Having issue with nrf52840 interface with sim808 for GPRS connection. I am trying to interface nrf52840 with sim808 using UART. But only AT and ATD command reply i can see...
I have a custom board with an application that works fine.
But when adding a secure bootloader my board starts to act weird. I am using the RESET pin on the chip as an input...
Hi,
I developed an application for the NRF52840 development board with Mbed-OS and now I would like to get it running on the NRF52840 Dongle.
Is this even possible?
...
Good evening,
We are trying to flash the bootloader DFU debug example using 10056 ble debug example code to our nRF52840 based board.
Everytime we try to flash, we get...
Hi Nordic,
My team and I are looking to purchase the NRF52840-DK for the purpose of testing long range coded-phy for bluetooth 5.0 applications. We would like to ask if...
Hi all,
When I do some tests on chip of nrf52832,the chip sometimes receive an error packet: the crc status is ok,but the length field is random.The reference documents...
Recently i have purchased nrF51 Dongle.
Am using Windows 10 (64Bit OS) on my PC.
1. installed nrfgostudio_win-64_1.21.2_installer.msi setup for flashing
2. installed...
We have a nRF based device being connected from a nRF51 dongle (PCA10031). We use pc-ble-driver 2.2.1.
We enable notifications and then we let the device running for a...
I had a working application and was trying to add DFU functionality to it. in order to do that i needed to add a bunch of files and i am at a point where i dont knwo what...
Hi,
For our continuous integration and deployment of firmware updates for our product, we want to test firmware upgrade paths from different versions. We are building a...
Hey,
I recognize that sometimes there are dependencies between silicon, board hw and software.
Is it ok to load the RF9160 mfw-m1_nrf9160_0.6.8-alpha firmware on nRF9106...
