My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
Hello, I have a question.
1. When ancs is reconnected, the machine will be reset, and the software will catch the log as follows.
As long as there are a large number of...
Hi Nordic,
I am using SDK 12.3.0, S130 2.0.1 and PCA10028 nrf51 DK.
I would like to know what would happen in the following situation.
During central and peripheral...
I noticed that in SDK SES projects, the linker file is generated every time the project is build. However, there is no memory map file specified, only a section placement...
I program in nrf52840 using thingy sdk
I succeeded in receiving the motion service.
The output speed of some motion services is too fast. such as raw, heading, gravity...
Greetings!
I'm new in the Nordic Dev Zone, so I apologize if this has been asked before. I just wasn't able to find a satisfying answer.
I read in this foruns that there...
dear
i am using this proj to get dfu functional
nRF5_SDK_14.2.0_17b948a\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\main.c
i add some code in main.c...
Hi all,
I want to see the value of the radio registers, especially the Tx power register, but i can see only the cpu registers in the register window.
I'm using segger...
Hi there,
I am using a nRF52840 development board, I've been able to get the blinky app to work. However, when I put the ble_app_blinky on the board, I am unable to discover...
Hello
Could you provide the compiled code (hex) for the application running by default on the nRF9160DK ? For some reason I am unable to rerun it from the source code provide...
Our products are based on nrf52832 / nrf52840 chips as application mcu which run freeRTOS.
One of high priority task implements algorithm for controlling motor (using QDEC...
Hi,
my BLE device is NRF52840, I am using softedevice s140_nrf52_6.1.1
using the ble_app_uart example as peripheral .
I have a problem to send data to our android ble...
Hi,
I'm trying to erase flash pages from 0x1f000 to 0x28000 (page 31- 40) and for three pages (33, 34, 35) I get NRF_ERROR_FORBIDDEN.
I'm using softdevice 132, version...
We are using NRF51822 MCU on our PCB design and we have a problem that we can’t program it, uKeil doesn’t recognize MCU. It seems that then we start programing NRF51822 it...
Hi,
we found problem with PID, we send individual messages to many nrf24 devices. When we have for example only 2 devices we have losses of around 40-50% but its not a problem...
Hi,
I am following below step for Installing micro_ecc_lib_nrf52.lib.
Install version 4.9-2015-q3-update of the GCC compiler toolchain for ARM. You can use ARM...
