I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
Hi there,
I've already downloaded ble_mesh_v0.9.1-Alpha SDK and I can use arm-none-eabi-gcc to compile it, one thing I want to know is that how can I switch HWID to 52 in...
Hello,
I'm trying to use ble_app_hrs_rscs_relay_pca10056_s140 on a nRF52840 Preview DK using example from SDK 13.0.0_04a0bfd.
When I copy the precompiled .hex file in...
Hi,
I'm trying to add another element with a simple onoff model to control a second LED on the same server node.
I get APP_ERROR. I try declaring m_server0, m_server1, generic_get0_cb...
Hello,
I want to use at the nRF52832 a temperature sensor TMP108 and an EEPROM via TWI bus which are connected to Pin 5 (SDA) and Pin 6 (SCL). I made a lot of time until...
Hello,
I have a custom board with a Taiyo Yuden chip (it integrates an nRF51822 QFAC chip, 2 crystals and the BLE antenna).
I program it using SWD. I succesfully uploaded...
Hi,
I'm trying to use nRF52832 by external oscillator(ash7k-32.768KGZ-T).
When i use SDK13, i just add clock setting like below.
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_Xtal...
Hello,
I'm using the SDK 14 and the FDS library.
I'm a bit confused about one thing :
FDS uses Flash Storage to write to flash.
Since SDK14 Flash Storage can work...
Working with: examples/ble_peripheral/ble_app_uart . I would like to change on_ble_evt priority level so that UART IRQ handler has lower priority then softdevice event dispatching...
Hi! I'm using openthread with custom-made board with NRF52840. During development of lowpower thread application I found out one big problem which i couldn't resolve. I've...
Hello i am now implementing a nordic52832 project On this
nRF5_SDK_14.0.0_3bcc1f7\examples\proprietary_rf\esb_ptx
nRF5_SDK_14.0.0_3bcc1f7\examples\proprietary_rf\esb_prx...
