I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Greetings -
I am working on a peripheral-heavy project. Many of the devices seem to work Just Fine with VDDio of 1.8 volts. On device seems to be having fits and I need...
void Gzll_TxSuccessCallback(uint32_t pipe)
void Gzll_TxFailedCallback(uint32_t pipe)
More than two functions are not accurate judgment
GZLL agreement return function cannot...
I try to implement this library to my code.
uint32_t settings_set_erase_flag(int32_t flag)
{
uint32_t err_code = fds_write(flag, ERASE_BOND_FLAG);
return err_code;...
Hello I have this error:
Checking installed packages
pyside: 1.2.4
pyqtgraph: 0.10.0
numpy: 1.12.1
pynrfjprog: 9.0.0
Warning: The software is tested with PyQtGraph...
I wrote a peripheral similar to NUS. Then I use the multilink central to connect to 3 of them. First two are fine. But when the 3rd is added, the 3rd one would connect, but...
Hi,
I want to make an BLE_UART dongle which will receive the data from the module(An external module is connected through UART) and it will be send over the BLE to ble_receiver...
I'd like to write some timestamps to a log variable in order to see how much time has elapsed between certain points in my code. app_timer.h has two functions that look suitable...
Hello,
I have a problem while combining peripheral examples in SDK13. I am trying to combine twi_sensor and uart but when I do this in uart folder, compiler gives following...
Hi support team,
We met an issue for connecting our device built in nRF51822 to Android device.
The nRF51822 uses below firmware program:
nRF5_SDK_12.3.0_d7731ad...
Hello,
I am working UART_BLE_APP , my query is when we transfer the data form smartphone application to the device where the data will get stored in device and can we access...
I have created a characteristic for sending up to 60 data bytes in a buffer using a sequence of 20 byte notifications sent to an external device. This works quite well for...
Hi,
What is an optimal transmission power to maximize the coded PHY range, but still stay within ETSI regulations? Can nRF52840 actually exceed the regulations if I set...
Controller:
nRF52832-QFAA
Reference project:
nRF5_SDK_11.0.0_89a8197/examples/dfu/bootloader/pca10040/dual_bank_ble_s132
Question:
The idea is, to store a init_DFU_by_flag...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 OTP version?
By the way, my development kit and board 0 seems have issue and cannot...
Hi
I use LESC sdk & nrf connect app
How can I know if my nrf51 device and phone are bounding through LESC?
From nrf connect( ios ), how can I know from nrf connect...
