Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
HI! I am trying to decrease the memory use of my application that is built for a nrf9160 and noticed that tfm creates a 256kB partition that it only uses around 99kB of. RIght...
nRF54L15 has RRAM with error correction codes (ECC) built in, with autocorrection.
I guess ECC errors could either happen due to a power loss during a write (when reading...
i am working with the nrf7002+nrf5340 ns when i run the excercise solution and press the button a couple of times, i get this error *** Booting nRF Connect SDK v3.5.99-ncs1...
I am bringing up a brand new laptop for devlopment.
I downloaded and installesd nRF Connect, SDK 2.6.0, SDK 2.7.0 and SDK 2.8.0. The SDK 2.9.0 installation failed.
I...
I plan to use an ESB as a low latency and high speed protocol.
However, there must be multiple hosts on one network.
Hosts or devices must be able to communicate with...
Hi,
I have a design which mostly follows the reference designs.
I've added a Resistor Network R16/17/24 to allow a UFL connector to connect to the ANT and isolate...
Hello, I really need some help to connect a central nRF52 DK board to a peripheral that was provided to me. This peripheral can connect to a smartphone using nRF Connect and...
NCS 2.7 with Toolchain 2.7
Launch build from Visual Studio
Sysbuild with mcuboot and custom application, custom board
Although the application itself updates when VERSION...
In our custom board nrf5340-nrf7002, tried system_off(C:\ncs\v2.6.1\zephyr\samples\board\nrf )sample to check power consumption.
But it measures 0.60mA Is there any config...
Hi Nordic DevZone team,
We would like to get nPM Power up for nPM2100 because it seems not to be supported for nPM2100 in nRF Connect.
We are plannning to let the customer...
I've worked with the nRF5 SDK in the past, and I've started exploring the nRF Connect SDK for future projects. I've taken some of the courses offered through Nordic (great...
I've just launched VSCode for an old project from the nrfConnect SDK launcher, and it seems like the plugin no longer works correctly. It does not search for custom boards...
I've been struggling with this for some time now and no matter how I approach it I can't quite get it to work. I'm essentially looking for something like the "maximum performance...
Hello, I have several development-related questions about the microphone functionality of the NRF5340 AUDIO DK in headset mode:
Is it possible to configure the device...
I saw in this video that there was a lipo battery being used with a nrf52 Development Kit and I read this in the spec for the nrf5340 Development kit:
1.7-5.0 V supply...
