Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Hello, I just wanted to share a problem I encountered and make some suggestions : I lost some time looking for a TWI problem while it was actually related to the pin reset...
Hello All,
I am using NRF51822 controller in my design.
I want to monitor battery voltage using ADC pin with voltage divider.
I have LIPO battery with 3.7V and 200mAH...
Hi Nordic Support, community,
After I flashed, the connectivity hex, ble_connectivity_s140_usb_hci_pca10059.hex from the SDK v15 downloaded after executing the patch on...
development software, with versions (SDKs, IDEs, SoftDevices, ...):
Computer platform, with versions (Windows/Linux/OSX, ...) Windows 10 Pro x64
hardware revisions (chip...
Hi,
I am trying to make a weather station with nRF52 feather and BME280. Currently I am making a measurement program. The base code is Custom:Heart Rate Monitor Example...
Hi friends I use nrf51822 with sdk12.3 version and I want to use infrared receiver.
What method should I use to write the infrared receiver code?
Also, does nrf51 have...
Hi,
I'm able to send arbitrary information to the host using generic HID descriptor (uses vendor defined page). There is no driver issue. I'm also able to connect to the...
I am currently downloading softdevice (S140) on our custom board using P19 connector on nRF52840 DK. Our custom board also has nRF52840. It seems the dsoftdevice is downloaded...
nRF52832 & nRF52810 don't support the Bluetooth 5 Range Extension (Coded PHY):
https://devzone.nordicsemi.com/f/nordic-q-a/39532/is-it-only-nrf52840-s140-which-support-bt5...
Whenever I deploy an example to the Fanstel BT840F with Segger ES, the S132 SoftDevice is always also deployed to it. I have attempted to change references to this in the...
Hi,
nrfx_uart.c has a bug where, once there is a RX error, the receiver gets stuck in a disabled state forever. This is because p_cb->rx_enabled is never set true, so the...
hi, my name is tyto I just learned programming about nrf52832, before I used to work with Arduino, after trying to learn nrf52832, it turned out to be very difficult for me...
Hi,
I'am using SDK v15.0.0 with the BLE OTA DFU bootloader. Is there a possibility to access the bootloader start address for a static assert in the application at compile...
We have bought nrf52 832 development kit.
When we checking the kit in nrf52 utility than it detects the IC nrf52 840 .
Hence we have erased all the memory in the DK...
Hi everyone,
I am using the following files to configure uart for laser distance sensor.
Serial Library
I am able to write command to the Laser sensor and also the laser...
