Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
Hi,
I'm using SDK 13.1, SoftDevice 4.0.5 on nRF52832. I have an app which runs for a long time but will occasionally enter the hardfault handler from an address within the...
Hello,
I try to send multi notification in one connection interval, but I can only send one notification.
Hardware
Peripheral: nrf52832 costumed board (with BMD-300...
Hi,
I'm using nrf52 custom board designed for our project,For this we have P0.09 and P0.10 as rx and tx used for uart, when i configured this two pins as rx and tx it is...
Hi
I am running on a nRF52832 chip with following software stacks
Mesh SDK v3.1.0
nRF SDK v15.2.0
Softdevice v6.1.0
I am working on a use-case where I am processing...
Hi
I want to get a certification. I need your help because I am not currently in DTM mode.
The procedure I checked is as follows.
1. J-LINK , USB to Serial Converter...
Hello to all,
I am using nRF52840 with SES SDK15.0 version. My device is goes into sleep mode after sending data to server. But when woke up device for first reading data...
Hi,
Can someone please tell me in what scenario would a device advertise with two different addresses at the same time?
My device is an nrf52382 based custom PCB...
I am try to register nrf9160 DK sim card, but keep getting fail to fetch error. I had made sure that I am entering correct sim Id and the puk but so far no luck to getting...
Hi,
I am using NRF 52832 S132 sdk 15.2.0.
I am working with example project <install folder>\examples\ble-peripheral\experimental\ble-app_multiperipheral.
I added NUS...
Hi,
I am testing the at_client sample code in the nRF Connect SDK.
I want to change the default AT host com port to uart1 or uart2.
I tried to modify prj.conf but it...
