Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
I use s110 v7.1.0, nrf51822qfaa.
The write flash data using pstorage is OK ,before ble_advertising_start() function is start run.
But if I run the ble_advertising_start...
Hello,
I am using the nrf52pdk and am wondering if there is a way to force an output compare interrupt to occur. For example, lets say you want to generate an interrupt...
Hi,
on the nrfprog you can detect all connected Segger programmers.
If I have 10 Segger Programmers connected, I can address each of them with the nrfprog to programm...
Hi,
I am new to Nordic. Will someone help me figure out what is wrong with UVision V5.16a. I get sample codes from pack installer example the "ble_app_hrs_s310_pca10028...
I've followed the instructions here to try and get my J-Link debugger to run in bootloader.
I am using a newer SDK and SD (than the post was written for) so that may have...
Hi !
I have a rather strange problem: 1 packet is transmitted for 30 milliseconds.
I use iPhone-4s with iOS8.1 and custom board with nRF51822
In the firmware exists 4...
I saw that DA14680 from Dialog comes with a 30uA/MHz processor.
Although the clock can be programmed up to 96MHz, the 30uA/MHz is measures at 16MHz.
How can I get a...
Can you please clarify what the RBC_MESH_EVENT_TYPE_CONFLICTING_VAL is used for with the RBC mesh? I receive these events on the node that sets a value, but not the remote...
Does the bootloader from SDK v9.0.0 actually work?
When I try to use it (with S130 v1.0 in eclipse/gcc), I get NRF_ERROR_INVALID_PARAM from pstorage_register called in...
Hi all,
After receiving data from my host app, I am trying to write to write the data to flash with the sd_flash_write command. I have 3 pages of data to write, so need to...
Is it just me, or is the documentation for SDK 9 broken? When I try to access the end nodes(where the actual info is), I get a blank screen. I'm having to use the docs for...
Hi,
My nRf51422 based device holds bonding with single central device and once it bonded it will do whitelist advertising at connection lost (whitelist has one address)....
When I send the command to the 51822,so the 51822 ready to DFU,but wait for a long time,51822 is staying at a DFU state,that means 51822 can not work.How to solve this problem...
