Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
I'm new to Nordic devices and tools. I have experience with Eclipse but I was wondering if there is a guide to help with the creation of a brand new project under Eclipse...
Hi,
As have been discussed earlier there is a problem with iOS device losing CCCD values on reconnect or turning bluetooth ON/OFF.
A patch for the ANCS sample is presented...
Hello Gentlemen,
Is it possible to know the passkey before the BLE_GAP_EVT_PASSKEY_DISPLAY event?
my nRF sensor is set as a display only and my central is an Android...
Hi all,
we are using the nRF51822 together with another module that provides an 1.8V UART only (LO = 0V, HI = 1.8V). Other IC´s on the device are using 3V Vdd and are connected...
I would like to make two BLE single mode devices to communicate with each other and Bluetooth v4.1 supports that, I was wondering if any of Nordic's modules support v4.1?
Referring to page 58 of the reference manual there is a ANAEN control signal that will contect a gpio pin to a corresponding analog input
I am using GPIO P0.01 -> AIN2...
I have started "playing" with the nRF51822 eval kit and the LED-Button example explained in the nAN-36. I wanted to know how is the UART port configured but I have not found...
Is it possible to count pulses with the 51822 from an external device in the range of 250-15.000 pulses pr. second, while the CPU is powered down (softdevice sleep)?
I...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi all,
i am new to nordic and I working on the project to scan/locate iBeacon by using nRF51822,
I can't found a related sample code on SDK 5.2.
Is there something I...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I have built a board using a reference design for the USB dongle board for the NRF24LU1+. Now when I connect to the USB the system identifies the device as "nRF24LU1+ -F32...
Hi!
I just ordered nRF51822 and nRF8001 chipset from Digikey, not dev KIT. I want to develop product by ourself based on nRF51822 and nRF8001 chipset so I want to have all...
