Hello,
In an ongoing company project we use a couple of nRF51 transceivers forming a beacon enabled wireless sensor network consisting of one base station and multiple...
I want to count clocks in order to implement a watch. I use the RTC0 as my time-base and count mainly with this device. As it has just 24 bits it would not last for long,...
Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
I've got my custom PCB design assembled. Attached segger jlink, but it detects only 0.1 V, although Vdd is 3V.
How is the power measured?
What should I read on SWDIO...
Dear
Is there a possibility within Nordic SoC to make a passive RFID Tag which will connect to SmartPhone via Bluetooth?
Just like µBlue Series, but smaller and using...
I found the "S110_SoftDevice_Specification_v1.2.pdf" but not the "S110 softdevice release notes" mentioned in a previous question about DCDC usage. Where is that doc?
What...
I have been developing on a nrF51422 QFAAC0 chipset. That chipset required SDK 4.4 for soft device capability.
I requested the latest silicon (so I could develop against...
Hello,
I would like to build a tool in Python that allows sniffing/interaction with BLE traffic between nRFgo modules (nRF51822) and a Mac via the master emulator. I am...
I have bought the Bluetooth low energy evaluation kit nRF51822. It can be paired with a Nexus and a Sony Xperia without problems, but it does not appear at all on Samsung...
L.S.
Today I decided to have a look at SDK5.1.0 for nRF51822 which supports the S120.
It is deliverd as an msi file with (as far as I have noticed) no support for specifying...
Is there anything preventing anyone from uploading the tinyest image that simply dumps the entire ROM content on the UART?
This would sort of circumvent the HW locking...
Hello,
I use nRF51822 for my project and I would like to purchase some BLE packet sniffer. Does anyone recommend any sniffer? My purpose for that is debugging and check transaction...
On PCB layouts I often see that the HF xtal is oriented at 45 degrees relative to the orientation of the 51x chip (that is to say the edges of the the xtal and 51x chips are...
Hello Nordic expert,
Regarding the antenna load impedance, I can find the data in nRF24L01+ datasheet and it is 15ohm +j88ohm.
But I can not find the antenna load impedance...
hi,
now ,i have save the power,so need to close the spi interface at some time.
but when i call follow function (hal_spi_disable).
it see not close the spi interface, ...
Hello,
During programming bootloader provided with sdk
I get some messages in Command window in Keil.
Load "C:\Keil\ARM\Device\Nordic\nrf51822\Board\nrf6310\device_firmware_updates...
Since I'm writing code for my own board, I decided to create my own board.h file to hold the board-specific definitions.
However, I can't do this without hacking the SDK...
Hi,
We have two services, apple ANCS and Alert Notification on iOS. We try to connect it with 51822. There is an exception case the the alert notification function not...
