Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
We've been working on a product that utilizes a NRF51822 chip as well as WS2812B NeoPixels. Since there have been numerous posts about it here we've decided to release our...
Due to limited resources we are looking for someone who can help us with making a custom profile.
You are preferably in the Stockholm area and have done this before.
The...
Just putting this here in case anyone else comes across this issue, esb_arm.lib and gzll_arm.lib don't appear to implement the work-around in PAN 18(in the version I tested...
URGENT
First of all, I have to mention that I dont understand PPI.
I have application which uses PWM to control a pump which is connected to the nRF52. To the nRF52...
What would be the payload size? That is, without any ble involvement? I assume it's 31 bytes? Or maybe this question is invalid since you can transfer unpackaged, raw data...
Issue: when the battery level is requested for the first time from mobile its responding correctly. but, when it is requested for the second time from mobile, disconnection...
We are trying to import blinky example(Keil project) to SES, we could succesfully build the eaxmple and dump into nRF52-DK, example is from SDK12.1. After we dump into kit...
Hi, I'm planning to create a custom PCB that uses nRF52832-QFAA.
Currently, I chose the Q22FA12800025 32MHz crystal to use, which is the same one in the PCA10040, I believe...
Hi,
I use nRF51822 with 256k flash and external sensor, and i want to write the data i receive from it via SPI to internal flash?
After the data received i want to send...
I've seen a few posts in regards to the usage of MCP in a windows virtual machine. From what I can gather, this setup just will not work, however I haven't really seen an...
Hello:
I was wondering about the random addresses programmed into the FICR on some of the devboards that I have. I read the devzone and it appears that the DEVICEADDR is...
I read that the DEVICEADDR is always in the advertising packet, so i need to take these data from the master each time that a slave is conected to them. I trying do something...
I'm using nRF52+SDK11.0.0+s132. In the ble_hrs PCA10040 example, the following are defined:
BLE_STACK_SUPPORT_REQD
BOARD_PCA10040
NRF52_PAN_12
NRF52_PAN_15
NRF52_PAN_20...
Similar to the thread posted here , I am trying to merge SD+bootloader+application and flash this to a nrf52 using the Segger programmer. This saves us a huge amount of time...
What is the best way to start a new nRF52 project, on a custom PCB?
I have a custom PCB, with nRF52 module. I use IAR, with ST-LINK V2
Say to test the GPIOs, do I start...
I took a look into the PCA10040 and the differences from PCA10036, seems to be minimal...
NFC connector and some breaking points. My question is: if somebody from Nordic...
Hi,
I am new to the nrf52. I want to implement the code that gives me current date and time value based on default set values.
for this i need to read the current counter...
