Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
Hi,
We are using the nRF905 device in an application where it needs to switch between auto-retransmitting and sending single packets, due to it communicating with several...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi all,
What is the maximum data rate for the nRF24AP2 when using the Synchronous serial interface?
I cann't see it in the datasheet.
Is there anyone can answer me...
Hi,
In my design, there is a tag used by 24l01,It can transmit the temperature value.In the tag, the parameters are like this:
addrofch[0] = 0xe7;
addrofch[1] =...
Hi
An unprovisioned device will advertise a beacon and the spec says that it shall be advertised with non-connectable and non-scannable undirected advertising events
...
Hello there,
for a project I would like to use the Arduino Primo core with the nRF52832 chip to read a NFC Tag.
I could not figure why it can´t read a tag even though...
Hi,
I've test the light_control example with the PCA10028 & PCA10040 recently. The PCA10040 was test and it works normally, but the PCA10028 does not.
I have also checked...
I am working on an application that allocate data dynamically at initialization, and my malloc/calloc returns NULL a lot earlier than I expected.
Using a debug macro, I...
Use the E: \ Nordic \ nRF5_SDK_12 2.0 _f012efa \ examples \ ble_peripheral \ ble_app_uart \ pca10040 this routine
Run to chart a breakpoint on the resumption of here
...
Hi guys,
I'm trying to use the HFCLK to generate high resolution timing. Ideally at the millisecond resolution. I've written a layer around the nrf_drv_timer.c module....
Hi,
I followed the tutorials you made to start developing BLE applications for nRF52 series development board. Then I started to make my custom application (in fact, it...
Hi everyone,
I have been reading the Specifications of Bluetooth 4.1, mostly about Universally Unique Identifiers (UUIDs) for Services, Characteristics, etc.
I found...
Respected sir,
setup for programming = Eclipse-gcc-toolchain-setup
board = PCA10040
as per my way first take a ble_app_uart code startup my coading purpose.
then we...
Hi Guys,
I'm doing the following before putting my device to sleep. This works fine when I use NRF_POWER->SYSTEMOFF, but when I use sd_power_system_off(), it doesn't seem...
Hello,
I am using nRF52832 development kit. I used different examples to send data. But i couldn't accomplish to send data packet over 20 byte. The max data size is defined...
I'm planning to use nRF51422 QFAAE00 as ble central. I try to compile the SDKv10.0.0\examples\ble_central\ble_app_hrs_c and SD130. And another one as ble peripheral using...
Anyone had a successful attempt at using the fds(flash data storage) module( http://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5.v11.0.0%2Flib_fds...
Hello,
Today I stumbled upon very strange nRF52832 behaviour which I cannot explain. I am using two TWIM instances (0 and 1) and one SPIM instance (2).
First strange...
