Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I have a serious problem, when I use uart of NRF51822 QFAAC0 to receive data from another MCU, I found that it will lost one bit at same position everytime. my SDK is...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I have a sample program that is failing on sd_ble_gap_device_name_set with an invalid parameter.
It's calling BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode)
And then it passes...
Gentlemen: Do you have posted a copy of the original firmware that comes installed on the nRF51822 beacon? I have been experimenting writing my own app on that beacon, and...
Hi all,
I have an TICK interrupt on RTC1 on nRF51822, but the program keeps cycling in the interrupt - as if the interrupt is never cleared?
Here's my code:
void...
Hello,
I am currently building up a little application on top of the ble_multilink_peripheral_example.
I would like to have the nRF Master Control Panel on Android to...
Hello,
First, my setup is as follows:
nRF51822 Rev. 3 dev board (PCA10028)
s110 7.1
SDK 6.1.0
I am developing firmware on the PCA10028. I am matching SPI to a custom...
Well not my best title. But I hope you can follow this explanation:
I added RTT to my project to replace UART. It works so far. But there is a strange behaviour...
Code...
I am trying to do OTA DFU on nRF51-DK from a BLE dongle (CSR 4.0) and gatttool from BlueZ. The image is compiled from blinky_s110_pca10028 example ( blinky_s110_pca10028.hex...
Hi
I want to program the S120 softdevice over an mbed HRM1017 ([link text] that uses nrf51822. I can program only with CMSIS-DAP or drag and drop over the drive. I am using...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
Hello,
as I couldn't manage to get my SPI Measurement working flawlessly when called from inside a timer handler I tried to work around it by just setting a flag inside...
Hi,
I have a setup :
nRF51822_QFAC Chip Rev3
Softdevice: S110 V8.0.0
SDK: V8
Code hangs at sd_softdevice_enable(). Clock Source I am using is NRF_CLOCK_LFCLKSRC_XTAL_20_PPM...
Hello,
Has anyone managed to get the Nordic_UART software to pair in Windows 8.1?
The heartrate monitor software pairs fine. Using show bluetooth devices, I can see the...
Hi,
I have a PCA10028 board. When I connect it to a computer the LED LD5 doesn't turn on at all, and no new USB connection pops-up in my computer. But when I connect it...
