I have a working project where pin 16 is configured as a low-level interrupt source.
it is working well with SDK 15.3
after porting to SDK 17.0.2, it is not triggering...
Hello Nordic Support Engineers and fellow developers ...
Just a note to thank everyone for help via this forum. I started very inexperienced with Nordic SDK a year ago and...
Hi,
I recently purchased a thingy91 for a project. I'm trying to follow instructions from a Nordic youtube video ( https://www.youtube.com/watch?reload=9&v=xQ7hDzRULJQ ...
I have a nRF5340PDK, Now I want to know the lowest power consumption of this chip in different condition, such as adv, connect, sleep. But I am not sure how to config the...
Hi, i am using:
-nRF 52 DK
-nRF 52832
-Sensor of Maxim Integrated
-SDK 17.0.2
I have some problems in handling the I2C through the nrfx module.
This is my ReadByte...
Hi, I have a set up consing of an nrf52840, a Raspberry pi and a Linux workstation, which communicate over IPSP following the IPSP sample from Zephyr OS. The nrf52840 is a...
Hello Nordic Team,
I am working with the nRF9151 DK and exploring audio output using the TLV320DAC3100 DAC.
I see that I2C is clearly available in the DK schematic , but...
Hi Nordic:
I use the nPM1300 to power the NRF5283 and external sensors. The nPM circuit schematic is as follows ， Please check for any unreasonable parts.
1 Charge and...
Hi All,
I try to connect nrf9160 to our azure space ( Azure IoT Central) using sample : sdk-nrf/samples/nrf9160/azure_iot_hub at main · nrfconnect/sdk-nrf · GitHub
...
Hello I already have a team on the PRO plan on nRFCloud and I would like to create a new team on the nRFCloud, using the same user as owner of both teams. According to: https...
Hello,
Is there an easy way to upgrade the CMake version that is used during the build process trigger from the nRF Connect SDK Extension in VSCode ?
I'm currently using...
I am using the older SDk 17_1_0 used in the Qorvo UWB sdk.
nrfConnect ->connected to -> controller ->connected to ->beacon, neither appear in scanner as expected once...
I can't define an Advertising file larger than 191 bytes, even in Extend.
Here's my code and proj.conf file.
My board is an NRF52840.
main.c
proj.conf
E...
Hello,
I'm working through the fundamental courses and trying to get my nrf54lm20 development board setup. After I have built and flashed the sample firmware to the dev...
I just upgraded my project (that runs on custom hardware with the nRF8233 using an Ezurio BL653 module) from nRF Connect SDK v3.1.0 to SDK v3.2.1 and the battery monitoring...
Hi, we have recently started developing with the nRF5340DK. We encountered several issues while configuring a FATFS on the external flash (mx25r64).
1. The sample code...
Hello
I am currently trying to develop an asset tracker based on your Asset Tracker Template ( GitHub - nrfconnect/Asset-Tracker-Template · GitHub ). While going through...
Hi,
I am trying to configure SWO logging in a sample project based on zephyr/samples/hello_world (source and config at the end).
I run this application on two targets...
Hello,
In document nRF54L15_qfaa_4L_config1_pcb_reference_layout_0_6 there is a representation of the PCB with 4 layers. The GND of C9 is not connected on the top layer...
Hi,
When configuring an nRF54LM20A for usb and then using the `onoff_request()` API to enable the HFCLK after that, results in spinning sys_notify_fetch_result() forever...
